answersLogoWhite

0


Best Answer

To remove a key that is stuck in the ignition on a Peugeot 406 HDI, make sure that the car is in park. Then try to remove the key. If this does not work, spray the ignition mechanism with WD-40 after pulling out the key as far as possible. Then work the key in and out until it comes out.

User Avatar

Wiki User

9y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove key stuck in ignition on peugeot 406 hdi?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Art & Architecture

Will a Peugeot 306 diesel starting motor fit a peugeot 406 diesel?

If the engine is of the same type it will. ie an XUD engine (1905cc) from one peugeot or citroen will fit another xud type but I do not know if it would fit on a HDi engine. On the 1.9 XUD the starter is the same on turbo and nonturbo models.


Remove the windscreen wipers on peugeot 406?

If you want to change only the wipers, there are some clips over windscreen wipers. You have to lift up (with your hand) the wiper and un-clip, place the new and then clip again. If you want to remove the hole system you have: *to open the hood *at the beginning of wiper construction there is one big screw remove this with a key (it might stack, so you may hit it a little bit to unstack or use oil) Then you are done. You have removed the hole windscreen wiper system.


Was there really a huge pit in Sparta?

All cities had pits into which they threw their rubbish and executed criminals and enemies. Sparta's pit was on the slope of Mt Taygetos a few km outside the city. It ceased to be used from 406 BCE.


Is it who or whom the gods wish to destroy they first make mad with power?

To use those words properly there is a trick. Just substitute the word he for who and him for whom. Which ever sounds right, is right.


What is the maximum temperature a 406 small block Chevy should run?

Hey Andrew==It isn['t uncomon for the engines to run 235-240 deg nowdays. Make sure the cooling system is in good condition and the cap is holding the proper preasure. GoodluckJoe

Related questions

How do you change the ignition coils on a Peugeot 406?

How do you change the ignition coil on a peugeot 406 coupe?


How would you remove a starter motor on a Peugeot 406 LX DT?

how do youremove a starter moto on a peugeot 406 please


How do you remove a fuel pump peugeot 406 2.0 lx petrol?

Slowly


How do you remove a driveshaft off of a peugeot 406?

This is a complex procedure, get a manual for this vehicle.


Peugeot 406 reversing lights staying on?

probably the switch stuck on. pull out fuse in mean time


How get 406 peugeot started as immoblizer will not work?

Had the same problem on my 406 coupe 3.0ltr-Try turning on ignition and pressing the keyfob-worked for me, good luck!


What is the wrench symbol means in 2000 peugeot 406?

The wrench symbol is the service indicator. On the 406 the wrench symbol is displayed with milage to service when ignition is switched on.


Where the hom on the Peugeot 406 2.0hdi?

WHERE THE HOM ON THE peugeot 406 2.0hdi out sade


Diagram of front suspension on Peugeot 406?

were will i get information for 1996 peugeot 406 petrol


How do you replace a heater matrix on a Peugeot 406?

not an expensive job to do. part cost about £10 but apparently it is an awkard job as a part of the dash on passengers side needs removing to get in at it. how do you remove a heater motor from a peugeot 406 do you have to remove the full dashboard or just the glove compartment


After changing the fuel fitter on a peugeot 406 hdi how do you bleed it?

turn on ignition wait 15 second and start hdis are self bleeding


When was the first Peugeot 406 car made?

The first Peugeot 406 was made in 1995. It was made by a the French Automaker Peugot to be a family vehicle. The 406 was last made in 2003 and then was replaced with the Peugeot 407 model.