0
Start by pulling the horn button off of the steering wheel, just grab it and pull, you'll see a big nut in the middle you will need to remove it and at this point you will need a wheel puller to remove steering wheel, probaly can rent or borrow one. Then it's a screw that holds the turn signal in place, pay attention how it goes and remove, next remove the screws holding the turn signal assembly in place. You'll have to wiggle it around to get the 4 way flasher button to come out with the assembly, leaving the wires intact just pull to the side out of your way. Now theres a outside snap ring around the splined shaft below where the big nut was, very hard to see it helps if you have someone to push down on the steering wheel lock disc, that's the black disc with teeth around the outside. Once you get the snap ring off the disc will pull off also, At this point put key in OFF position and remove the last screw behind where disc was, should be in the upper right. This screw holds the lock cylinder in place it is longer than the others. Now gently pry the lock cylinder out, Don't move anything inside of steering coulum until you get new cylinder back in place. Then just reverse what you did to put it back together. I will admit snap ring is tough to remove, but process is kinda simple. On a scale of 1 - 10, i'd rate it a 4. Hope this helps..
What else can I help you with?
How do you change the ignition lock cylinder in a 1989 Chevy Cheyenne when there is a key broke off in the ignition and it won't turn?
A locksmith may be able to remove the broke key and make a new one. Or just replace the ignition.
1997 Chevy blazer won't start after it rains what is the problem?
Ignition control module.. located under the distributor The distributor cap is probably cracked and moisture is getting into it. Replace the cap .
What happens when you have just changed the crank positioning sensor on a 2002 Chevy blazer 6 cylinder and it still will not start?
Was that the only code that caused you to replace it? Do you have it close enough to sense again.
Why is the Security light on in a 2001 Chevy Blazer that doesn't even have a security system?
The 2001 Chevy Blazer does have an ignition security system that is controlled by the computer in the vehicle. The light might come on because of an error that is coming up in the computer due to a key problem or an ignition problem. This is a common issue with the 2000 and 2001 Blazer.
On a 93 Chevy cavalier- do you have to pull steering wheel to replace ignition switch?
yes
How do you remove the Ignition Key Lock Cylinder to replace it on a 1976 Chevy Blazer?
this site will help
How do you install the ignition lock cylinder on a 84 Chevy blazer?
You will need to attach the wiring harness to the end of your 1984 Chevrolet Blazer ignition lock cylinder. Slide the cylinder into the cylinder slot. Secure the ignition lock cylinder with the retaining ring.
How do you replace 1981 Chevy ignition cylinder?
== ==
How many ignition coils on a 2001 Chevy blazer?
There is 1 per cylinder.
How Do You Replace Ignition In 1992 Cavalier?
how do you replace ignition switch on a 1992 Chevy cavalier 2.2 4 cylinder
How do you replace an ignition lock cylinder on a Chevy S-10?
Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.
How do you replace the ignition cylinder on a Chevy Beretta?
Go to autozone.com they have this information on their website.
How do you replace an ignition switch for a 2000 blazer?
You will need to remove the retaining ring at the top of your 1978 Chevrolet Blazer ignition switch. Slide the ignition barrel out and remove the wiring harness. Reverse the process to install the new ignition switch.
How do you replace ignition lock cylinder on a 2004 Chevy aveo?
I broke my key in the ignition and cant get it out. My only option I can see, is to replace to tumbler. How do I remove it?
Where is the crankshaft sensor on 1995 blazer 6 cylinder S10?
Chevy did not use a crankshaft sensor in 1995.If it won't fire then I would check the ignition module in the distributor and more then likey replace it. Also check the ignition coil and WIRE / coil wire.
Replace heater core in 1997 Chevy blazer?
how to replace a heater core in a 1997 Chevy blazer
How do you a replace a ignition cylinder for a Chevy El Camino 1971?
To replace the ignition cylinder on a 1971 Chevy El Camino, first disconnect the battery to ensure safety. Remove the steering column cover by unscrewing the necessary screws, then locate the ignition switch and the retaining pin for the ignition cylinder. Insert the key into the ignition, turn it to the "Run" position, and press the retaining pin to pull out the old cylinder. Finally, insert the new ignition cylinder, ensuring it's secure, and reassemble the steering column before reconnecting the battery.
