0
You carefully pry it off. If it doesn't come loose easily from one pry point, move around the edge of the cover and try other places.
also you have to be careful as to not try to pry the plastic covering because you can break it. use a flat head screw driver and pry it off.
ANSWER: THERE is a small slit on the dome cover toword the passenger side insert a small flat head screwdriver and pop off.{just did mine}
What else can I help you with?
Can a 7 passenger Toyota sienna be converted to an 8 passenger van?
No, not unless you replace both second rear side seats. or remove the center arm rest. I own a 8 passenger version and It doesnt have arm rest on the seats.
What is the name for reddish brown pigment?
Burnt sienna.
How do you mix burnt sienna?
To mix burnt sienna, start with a base of raw sienna or yellow ochre for a warmer tone. Add a small amount of red, such as cadmium red or alizarin crimson, to deepen the color. For a darker shade, incorporate a tiny bit of black or ultramarine blue, but do so gradually to avoid overpowering the mix. Adjust the proportions to achieve your desired hue and intensity.
Why do codes P0325 P0330 keep coming back on 1999 Toyota sienna?
Trouble code P0325 means: Knock Sensor 1 Circuit (Bank 1) Trouble code P0330 means: Knock Sensor 2 Circuit (Bank 2) Need to replace Knock sensor
How do you replace the passenger side mirror of 2003 Toyota Sienna?
Hey Lee==there are screws on the inside of the door.Be careful as there are a lot of sharp edges there. GoodluckJoe
How do you replace a factory antenna on a 2002 Toyota Sienna?
"How do you replace a factory antenna on a 2002 Toyota Sienna?" I am talking about the whole assembly. Thanks
How do you replace the low beam headlight located on a 1999 Toyota Sienna?
Open the hood, remove the rubber boot, unplug the wire connector, unclasp, remove the burned bulb and replace with the new one.
Replace water pump on Toyota Sienna?
Remove engine and transaxle assembly
How do you replace a rear wheel bearing on a 1999 Sienna?
I assume that it will be like a 1998 Sienna van. There is a sealed bearing in the hub assembly and you change the whole assembly. There are four bolts that hold the hub assembly to the suspension.
How do you replace the rear wheel bearing on a 1999 Sienna?
I assume that it will be like a 1998 Sienna van. There is a sealed bearing in the hub assembly and you change the whole assembly. There are four bolts that hold the hub assembly to the suspension.
Where is the evaporator for a 98 sienna?
Its located on the passengers side inside the a/c case assembly.........
Where is the Fuse for headlight in Toyota Sienna 2000?
The fuses for 2000 Toyota Sienna is located in the engine compartment. The fuses are labeled as slot 12 and 13 and are rated at 15 amps.
Can you buy the brackets that hold the headlight-turn signal assembly to a 2001 Toyota Sienna?
yes, try a junk yard before going to a Toyota dealer
Where is the Toyota sienna fuel filter 2008 located and need to replace it?
In the fuel tank.
How do you replace licence plate light on a 2006 sienna?
To replace the license plate light on a 2006 Toyota Sienna, first, locate the light assembly at the rear of the vehicle. Use a flathead screwdriver to gently pry out the light assembly from the housing. Remove the old bulb by twisting it counterclockwise and replace it with a new bulb, then reinsert the assembly back into the housing until it clicks into place. Finally, test the new bulb to ensure it is working properly.
Where is the fuel filter for 2009 Toyota sienna located?
The fuel filter for a 2009 Toyota Sienna is located inside the fuel tank, as it is integrated with the fuel pump assembly. To access it, you typically need to remove the fuel tank, as there is no separate external fuel filter. It's advisable to consult a repair manual or a professional mechanic for the exact procedure if you need to replace it.
How do you replace a starter in a 2000 Toyota Sienna?
How to replace a starter in a 2009 toyota sienna
