0
Disconnect your battery cable for a bit and then reconnect.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you reset the Low tire warning light on 2009 Ford Edge Limited?
The owners manual from my 2010 Ford Edge Limited states that you must drive the vehicle for 2 minutes at over 20 mph before the warning light will reset.
How do you reset the check engine light on a 1997 Ford Ranger?
The check engine light codes have to be read and removed with a scanner on anything after '96.Auto Zone will do it free.GoodluckJoe To reset the "check engine" light, simply disconnect the battery for a moment and it will go out. This worked for me on my 98 Ranger. try checking the co2 sensor. A sure fire method, if you can access the fault codes, is to remove the jumper wire while the codes are displaying. Pull the codes from the computer, match the code to the troubleshooting procedure, follow the procedure to find the source. Repair the source, light will go out if that was the only problem. There are "monitors" or self tests the computer runs the car through a drive cycle, if a problem occurs, it may not run all of the self tests until that problem is taken care. Therefore, another problem may exist. It is emission related. OR hook up a scanner that is capable of clearing codes, and hope that none are still active. Pukenstein@aol.com Unless it is a hard code...OBDII hard codes will not reset simply by fixing the problem..they have to be reset with an OBDII scanner Advance Auto Parts has em too
Where is the fuel pump reset switch and how do you activate it on a '94 Ford Ranger 4.0 V6 2-wheel drive truck?
It is about 18 inches up from the floor on the pass side of the cab. Find it and you will see how to reset it.
Why wont your ford tauras start unless jacked up?
reset fuel cut off safety switch after being jacked.
What does the wrench warning light mean on a 2006 Ford F350 Diesel?
It means generally that there is something wrong in the engine bay. The best way to find out is have the codes read by buying a code reader yourself or taking it to an agency for an assessment. Good code readers cost about $ 100 but can save you lots.
What kind of oil for a Ford freestyle?
( 5W-20 ) for the Ford Freestyle ( 2005 , 2006 , 2007 )
How do you reset check engine light on ford freestyle?
to reset "check engine light"- (on '05 freestyle) remove the negative cable from the battery for at least 20 min. It worked for me
What Oil type ford freestyle 2006?
5w-20
What is the torque specification for 2006 ford freestyle?
intake manifold
How many valves per cylinder does the 2006 ford freestyle 3.0 liter engine have?
In a 2006 Ford Freestyle your 3.0 liter DOHC Duratec V6 engine has ( 4 valves per engine cylinder )
Does a 2006 ford freestyle have a timing belt or chain?
In a 2006 Ford Freestyle : The 3.0 liter DOHC , Duratec V6 engine has ( 2 ) timing CHAINS ( 1 timing chain to each cylinder head )
How many liters of oil in 2006 freestyle?
5.7 liters ( 6.0 U.S. quarts ) with engine oil filter change , according to the 2006 Ford Freestyle Owner Guide
What is the fram oil filter number for a 2006 ford freestyle?
fl 820 s
How much does a mechanic charge to replace fuel filter on 2006 Ford Freestyle?
$8.00
How do you turn of traction control light in 2006 ford freestyle?
you break it then you jbdghfiuglbgrtgldjnfgx bnzdgthndlx
How can you reset the computer of Ford Taurus 95?
You can reset the computer on a 95 Ford Taurus by connecting an OBDII reader to the vehicle. It can then reset all codes within the computer.
What kind of oil filter does a 2006 ford freestyle use?
According to the 2006 Ford Freestyle Owner Guide ( and one of Fords websites ) The ( Motorcraft FL-820-S ) engine oil filter is used with the 3.0 liter Duratec , V6
