Want this question answered?
Usally U turn the key on without starting & pump the gas pedal 3 times with in 30 seconds. ??? I'm not sure about that answer. I usually press the button on the overhead computer where the service interval required shows zero, then hold the RESET button until it goes back to 3,000.
Take the car to your nearest VW garage n get the thing serviced - If a service is needed! Otherwise: Note: the Service Reminder Indicator displays 3 messages: OEL, IN 01, and IN 02. These display to alert the driver to follow the items listed under the manufacturer's service interval. To reset the message displays, turn the ignition switch on. Press and hold the odometer reset button "A" located below the speedometer. Turn off the ignition while holding the button. "OEL" will display on the indicator. Press and hold the lower digital clock reset button "B" until five dashes appear in the display. If needed, press the odometer reset button until "IN 01" appears and then press the clock reset button until five dashes appear. If needed, press the odometer reset button until "IN 02" is displayed and then press the clock reset button until five dashes appear. To exit reset mode, turn the ignition switch on and when "IN 01" appears, turn the ignition switch off.
according to autodata service lamp can only be reset using suitable diagnostic computer Dr.Pedro VolksWagen service technician
Directions to do so are listed in the drivers manual. Key on, engine off. Press the gas pedal down three times in five seconds.
The trip opometer can be reset and doesn't change the odometer. The trip opometer can be reset and doesn't change the odometer. An odometer is a continual counter of distance and a trip odometer measures from point A to B and can be reset.
How to Reset the Service Interval on a Nissan Navara 2.5 Read more: How to Reset the Service Interval on a Nissan Navara 2.5 | eHow.com http://www.ehow.com/how_7479944_reset-interval-nissan-navara-25.html#ixzz0eMmf6XGz
mercedes b180
with the dealer computer.
This is a service interval reminder. You can hold down the two buttons on your guage cluster at the same time. to reset each Service "interval reminder".
AnswerCars today use an internal clock and the odometer reading stored when the last service interval was reset to count down to the next service interval.
Service Light Reset - Citroen Xantia (1997 on)Using button located within speedometer dial.Switch the ignition off.Press and hold button.Switch on the ignition.Keep the button depressed.Service Interval and "spanner" symbol will illuminate for five seconds
unfortunately this is not possible without service workshop dignostic software
try this, turn your key to run ( not start ) press the gas pedal down three times, then turn the key off. Turn the key to start and the light should be off. To reset your service interval counter: Turn the ignition on Press the 'select' button momentarily then Press the set button for at least 2 seconds The counter will reset to 7500 miles
Dealer
It is quite simple. Turn ignition on, but do not start, press MENU, until display reads "service interval". Check the interval value displayed, and simply change it to another value using STEP. Press and hold RESET for approximately 3 seconds. Scroll further and display will read "change service interval". Select yes. Turn off ignition.
resetting requires special fiat/alfa/lancia computer Examiner
1) Procedure to check/reset service status – Distance counter 􀂃 Switch ignition OFF 􀂃 Press and Hold left instrument panel reset button, switch ignition ON to position ‘I’ (accessories) 􀂃 Keep reset button pressed for approximately 5 seconds until the LCD displays ‘RESET SIA’. The distance to service (e.g. 2150 miles) and the service type (e.g. Inspection/oil service) will be displayed. 􀂃 Has the ‘Reset Distance’ limit been reached or exceeded? o NO - Follow instructions in section 2 below o YES - Follow ‘Reset Distance Counter’ instructions below Reset Distance counter procedure 􀂃 Press and hold left instrument reset button for 5 seconds. ‘RESET’ will begin to flash on the LCD display. 􀂃 To reset distance the left hand button should be pressed before the ‘RESET’ message has flashed 5 times 􀂃 The LCD will display ‘END SIA’. Switch ignition off 2) Procedure to check/reset service status – Date counter 􀂃 Press left instrument panel reset button once 􀂃 The LCD will display ‘RESET SIA’ followed by the service due date. 􀂃 Has the ‘Reset Date limit been reached or exceeded? o NO – Press the left instrument button once. The LCD will display ‘END SIA’ to indicate the service interval check/reset procedure has been cancelled. o YES - Follow ‘Reset Date Counter’ instructions below Reset Date counter procedure 􀂃 Press and hold left instrument reset button for 5 seconds. ‘RESET’ will begin to flash on the LCD display. 􀂃 To reset distance the left hand button should be pressed before the ‘RESET’ message has flashed 5 times 􀂃 The LCD will display ‘END SIA’. Switch ignition off