The noise is difficult to diagnose over a forum, but if the battery is charged correctly, and is hissing as you put it, the starter motor may not be working correctly, get a second opinion from a garage
The CCA of batteries varies from one battery to the next. Normally the higher CCA the more the battery costs. Just buy one that is at least as big as the OEM battery. << >> CCA is not equivalent to ampere-hours. One ampere-hour is equal to 3600 coulombs (ampere-seconds), the electric charge transferred by a steady current of one ampere for one second. A coulomb is one ampere times one second. An ampere (and coulomb) is 6.241 × 1018 electrons in one second passing a point in a circuit. CCA is the max number of amps a car battery can deliver in each second until it is discharged below a certain amount of electrons. So how many amp-hours in a car battery? It depends--on the size of the battery. Larger cells mean more amp-hours stored in each cell.
I can say that it is not to replace but you can do something to have the Cr1616 works on a unit using CR1632. As the first number on the CR code corresponds on the diameter of the battery it means that both will fit it on the unit bettery lying pad. As the second number corresponds on the thickness of the battery then you just need to put a shim or something that will push the battery to properly fit in. This will enable the battery works on the unit. This is just a temporary workaround while you are looking for the right battery for your unit. Thank you and have a nice day.
A clicking sound when trying to start a car is almost always a low battery. The solinoid which engages with the ring gear isn't getting enough voltage to move it's gear. This causes a fairly rapid and regular clicking sound something like 6 or so per second. Attach a battery charger for 15 minutes or so or get someone to give you a jump. Then consider what the problem with the battery may be before you get stranded.
Intensity is the quality of being intense. In physics, it is the measurable amount of a property, such as force, brightness, or a magnetic field. In Earth science, the amount of damage caused by an earthquake. it can also mean the amount of energy that a wave carries past a certain area each second
You will need a second battery in series with the first battery to produce the 24 volts DC. To keep it charged the series connection will have to be manually changed to a parallel connection.
I edited your question since mobile phones can not be "trained" . Well first thing you may have to do is to reduce brightness and to shut off vibration . The second thing you may do and will help in maintaining a long battery life is only chargin your phone when its battery low and keeping it charging till its full . It is recommended you dont take you phone of the plug until its full. Avoid small chargings , but in the same time remove the plug whenever your phone is fully charged since keeping it in the plug will reduce battery life.
Check the date code on the battery. It is the first 2 characters. The second character is the year. Example D9 would indicate the battery was made in 2009. AC/Delco batteries reverse this so the first character is the year.
ADP is like a partially charged battery because there is still energy contained within the bond between the first and second phosphate groups. However, it lacks the "high energy" bond that exists between the second and third phosphate groups in ATP.
You will need a second battery in series with the first battery to produce the 24 volts DC. To keep it charged the series connection will have to be manually changed to a parallel connection.
Mine runs for about 6 hrs on a full charge, playing MP3's, 5 second back light delay, and lowest screen brightness settings.
Yes, for about .1 second, then it will blow the lamp. A 9v battery will however light three 3.5v lamps.
You can wreck the battery. Get a smart charger or trickle charger to avoid this problem.
I can if I charge 2 of them at a time. Most 24 volt chargers also have a 12 volt setting. What is hard to find is a 32 volt charger. We can charge a 12V battery with 24V charger, by connecting two 12V batteries in series i. e. the negative terminal of the first battery is connected to the positive terminal of the second, now the charger positive terminal is connected to the first battery positive terminal and the negative terminal of the charger is connected to the negative terminal of the second battery.
Assuming neither battery is used to start the engine, simply connect the positive (+) terminal of the first battery to the positive terminal of the second battery. Then connect the negative (-) terminal of the first battery to the negative terminal of the second battery. Connect the load circuit to the positive and negative terminals of one of the batteries as usual. You may want to charge the batteries separately before making the connection, since connecting a charged battery to a discharged battery will result in a very large current flowing from the charged battery to the discharged battery, possibly damaging the wiring or either battery.
I'd say that was a dodgey (broken) battery or firmware, send it back to wherever you got it.
Yes you can leave your laptop charger on once the battery is fully charged. however, modern Li-Ion batteries should never be run ar full capacity continuously. We recommend either removing the battery if you plan on using your laptop for a long period of time on the mains, or let the battery run down once a week and then recharge it again to keep the molecules moving within the battery. See our simple guide here on how to care for your laptop battery