0
Usually in a vehicle the ignition switch will contain four postions. This includes the On postion, off, start, and accessories. Although some standard cars may only contain 2 positions being the on and off.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the ignition cylinder housing on a car?
The ignition cylinder is the part you turn your key in to start the car, this is in its housing.
How much does it cost to repair a tumbler in a car ignition?
about how much does it cost to repair a car ignition tumbler
What does a ignition starter do on performance of a car?
The ignition starter has nothing to do with performance. It just starts the engine.
Why would everything be powered but the car will not start?
Ignition or ignition switch could be bad or the selanoid could have went out
Where is the ignition switch located on a 1986 Nissan 300ZX?
when you start the car up that's your ignition switch is located...
How do you set up positions of the ignition wires?
Make of car? Model? Year? Engine size?
How many ignition coils does a car have?
It depends upon cylinder in car. 3 ignition coils - 3 cylinder engine. 4 ignition coils- 4 cylinder engine.
Why does my 1999 Toyota V6 Camry Starter runs with ignition key off?
Most likely the ignition cylinder where you put your key before to start your car is broken. You have to remove it and test wires in different positions of the key.
What is the purpose of the ignition control module?
It sends the proper signal to the ecu to allow certain curcuits to close to allow power to the acc, on and run positions with the key.
What is a sentence that contains the word ignition?
I turned on the ignition in my car. "Houston, we have ignition!"
How do you get a locked ignition out of a 1992 Lincoln Town Car?
You can't get a locked ignition out of a 1992 Lincoln Town Car. Turn the ignition on to take it out
What is acc position on car ignition?
The ignition switch generally has four positions: off, accessories, on, and start. Some cars have two off positions, off and lock; one turns off the car, and the other allows the key to be removed from the ignition. When the key is turned to the accessories position, certain accessories, such as the radio, are powered; however, accessories that use too much battery power, such as window motors, remain off in order to prevent the car's battery from being drained. The accessories position uses the least amount of battery power when the engine is not running, which is why drive-in movie theaters recommend that the car be left in the accessories mode during the movie.
How much does it cost to repair a tumbler in a car ignition?
about how much does it cost to repair a car ignition tumbler
What is the ignition cylinder housing on a car?
The ignition cylinder is the part you turn your key in to start the car, this is in its housing.
How do you hot wire a 1992 ford ranger?
I am not sure why you need to know this but, nevertheless... To hotwire any car you need a "slim jim" or something else to unlock the car (if it is locked). Then, here are the rest of the steps. Step one Locate the ignition tumbler, the spot where you normally put your key. Remove the covers and panels around the tumbler. Step two Examine the ignition setup. There should be a panel with five to eight wires clipped to the rear of the tumbler. Remove the panel and try to manually turn the ignition switch using a screwdriver. If you can do this, then you are done! When you turn the ignition switch (usually with a key), it rotates a pin or lever on the back side of the tumbler. The panel is essentially a switch with four positions: off, accessories, full on and ignition. The different positions of the key correspond to each of these positions. Step two Research the color coding of the ignition wires for your specific car model. If you are not able to manually turn the ignition switch with a screwdriver, you will have to strip wires to hot-wire the car. Step three Locate the "on" positive and negative wires in the steering column. They should run up to the ignition tumbler and be color-coded. Step four Pull those wires from the ignition, strip a portion of each and twist them together. The car will now be on and ready for ignition. This is where you truly hot-wire a car. These wires carry a charge, which is why they are called "hot." Step five Find the starter wires and pull them from the ignition tumbler as well. Strip the ends and touch these wires together briefly. This should activate the starter, firing up the car. If you have done everything properly, your car will now be running. Do not leave these wires touching each other once the car is running. Step six Cover up any exposed wires to avoid painful electric shocks. Drive away and have your ignition repaired or a new key made so you do not have to hot-wire the car regularly. Courtesy of EHow.com at http://www.ehow.com/how_2044915_hotwire-car.html
What is the purpose of a car ignition system?
Start the car
What is the main purpose of a car ignition system?
Start the car
