0
not sure if it's the same on yours but on mine this is what i do. i leave the key in the ignition, i turn the ignition all the way back as far as it will go, tap on the key inwards and then try it again. on mine it's because my keys are worn down, yours might be the same, but it's worth a shot.
What else can I help you with?
Ford Ranger 2001 4-cylinder sometimes won't start battery alternator wires wires to battery and starter are good?
Will it even crank? If it won't, you have an ignition switch or lock cylinder going bad. If it does crank, just not running, then check to make sure fuel pressure is good and that the ignition coil is good. When exactly will it not start?
How do you remove the ignition lock cylinder on a 1997 astro van?
Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.
Why wont car start after changing ignition lock cylinder?
It may not be connected right.
What do you do if your key is stuck in the ignition of a 1999 Pontiac Gran Prix.The ignition will not turn to the lock position for me to remove the key?
is it a ford? push the key in further and then turn it
How do you program an ignition lock cylinder for a 2000 Toyota Avalon?
When you say program, do you mean make the ignition cylinder so you can insert the key and turn it to start the vehicle? If so you can bring it to a lock shop and have them program the key.
How do you program a 2003 Ford Ranger keyless remote?
Instructions # Step 1 Sit inside your Ford Ranger with all the doors unlocked and closed. # Step 2 Place the key in the ignition and cycle the key from "On" to "Off" eight times, without actually starting the ignition of your Ford Ranger. # Step 3 Wait for the car to automatically trigger its locking system, at which point it will lock and unlock. # Step 4 Press the lock button on your remote to lock your doors. # Step 5 Remove the key from the ignition in your Ford Ranger and lock the doors manually. Try the remote again to make sure the programming was successful.
How do you bypass the electronic chip in your key for a 99 Ford Ranger?
The easiest way to get around the Transponder Chip in your 99 Ford Ranger is to have a chip programmed and mount it under the steering column cowling close to the inductor coil on the ignition lock. That way you can use non Transponder keys to start the vehicle.
How do you remove and replace an ignition lock cylinder on a 1994 Ford Bronco?
Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.
How do you remove the ignition lock cylinder from a 1994 ford ranger v6 3.0?
To remove the ignition lock cylinder from a 1994 Ford Ranger V6 3.0, first, disconnect the negative battery cable to prevent any electrical issues. Then, insert the key into the ignition and turn it to the "Run" position. Locate the release pin or hole on the ignition switch assembly, typically found on the underside of the steering column, and press it while turning the key to the "Off" position to release the cylinder. Finally, pull the cylinder out of the ignition switch housing.
How do you remove a frozen ignition lock from a 1991 ford ranger It will not turn at all so the release pin cannot be pushed?
drill through the release pin
Ford Ranger 2001 4-cylinder sometimes won't start battery alternator wires wires to battery and starter are good?
Will it even crank? If it won't, you have an ignition switch or lock cylinder going bad. If it does crank, just not running, then check to make sure fuel pressure is good and that the ignition coil is good. When exactly will it not start?
Installation ignition lock cilinder ford focos 2000?
how can I do for installation lock cilinder ford focos 2000
How do you remove ignition lock key without key?
Removing a ignition lock cylinder from a 2002 ford windstar with no key
Does the ignition key for a 1996 ford ranger also unlock the door or is a separate key needed?
It only uses ( 1 ) key , unless a lock cylinder has been changed
Change ignition lock on 1970 ford maverick?
How do I replace an Ignition in a 1970 Maverick
You lost your keys On a 1987 Ford Ranger how can you remove the ignition to get a key made?
Either call a loclsmith or remove a door lock- may be easier access If you remove the ignition why not just put a new one in,it comes with a key
How do you remove the ignition lock cylinder on a 1997 astro van?
Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.
