0
brake pads are decently easy to replace for disc bakes, but more complicated for drum brakes.
for disc brakes all you have to do is remove the wheel, take off the caliper and depress the piston, then put in the new pads and put the caliper back on. the caliper is held on by 2 bolts on almost every car.
for drum brakes you have to take off the wheel and drum. the drum slides off like the wheel. but the pads in drum brakes have a bunch of springs and clips attached to them and you have to adjust a little ratcheting screw spacer. it can be done easily but requires slightly more thinking.
NEVER HIT THE BRAKE PEDAL WHILE ANY CALIPERS/DRUMS ARE REMOVED
it will cause the pistons to fall out and you will have to rebuild your calipers/drums
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you replace the front and rear brakes on a 2001 VW Beetle?
You will need a metric Allen wrench (7 mm).Jack up passenger side and place jack stand. Remove wheel. Take a screwdriver and work it in between brake pad and rotor. Once done, apply steady pressure on brake pad until you push the caliper piston as far in (toward engine) as it will go. You will need to remove caliper bolts. They are on the back of the caliper at top and bottom. Place Allen wrench in each bolt and turn wrench towards front of vehicle to remove. Once removed, remove caliper with brake pads inside. Match new brake pads with old and put new pads in like you removed the old pads. Place new pads and caliper back on vehicle and replace caliper bolts. If caliper and new pads do not slide easily back in place,you may need to get a large c-clamp and push piston back in caliper a little more. After you get caliper back on and tightened, get in car and pump your brake pedal until it is hard to push. This resets the brake pads. Replace wheel and your done!!
How do you change brake pads on a 2006 silverado?
* Lift truck using your floor jack (use jack stands for safety) * Remove rim * Remove bottom bolt on caliper using 3/4 inch socket * Loosen top bolt on caliper using 3/4 inch socket * Now pull caliper and it should swing up * Remove old brake pads by pulling ( Only your fingers needed ) * Install new brake pads * Grease back side of brake pads with your choice brake grease * Compress pistons with piston comressor ( I bought mine at an auto part store for $8.00) * Pull caliper back over brake pads * Screw in bottom bolt and tighten * Tighten top bolt * Put your rim back on * Follow same instructions for other side * Drink your favorite beer
What part of the brake system presses the front pads against the rotor?
The caliper holds 2 brake pads in
What are the signs that the rotors in a 2000 Toyota 4runner need changing?
If you're changing the brake pads and there is too little rotor thikness to turn it, it should be replaced. If the rotor is warped and is too thin to be able to turn to remove the warping, replace it. If the brakes "pulsate" when you use moderate brake pressure, the rotor is warped.
Why do brakes squeak?
if they screech for the most part it is a good indication you need new pads there is a metal indicator that when brake pads wear down will start scraping against the rotor now if you know the break pads are good or new screeching is common for the first few days if it continues it could be that you did not apply brake grease to the back of the pad where the pad meets the caliper if that's the case take them off and get a couple tubes of brakde grease (not that expensive) and put them on the back of the pads BUT DO NOT PUT THEM ON THE ACTUAL PAD WHERE IT WOULD CONTACT THE ROTOR that will make your brakes fail
Where can find instructions on changing brake pads?
There are many places where one can find instructions on changing brake pads. A good place is the website "edmunds" to find instructions on changing brake pads.
Is there somewhere I can get instruction on changing brake pads?
If you want to know if there is somewhere you can get instruction on changing brake pads because you need your brake pads changed, then the answer would be yes.
Where do you find a guide for changing a cars brake pads?
When wanting to save some cash and change a set of brake pads at home then it is possible to find help and advice on how to change the brake pads on the internet. Such websites as Edmunds have an article on changing brake pads, and the Halfords website also offers information about changing brake pads.
How do you make the brake pedal hard after changing your rear brake pads on your vauxhall vectra?
reverse then hit the brakes hard do this a few time and the self adjusters should adjust for you
Do you need to drain brake fluid when changing brake pads and rotors?
no
Changing brake pads 2002 dodge pickup?
how do change brake pads on a 2002 dodge pickup 4x4
Is it hard to change brake pads on a 1989 BMW 735i?
is it hard to change brake pads on a 1989 BMW 735i
Why does your rotor not move after changing the brake pads?
if when changing brake pads there is air in the system, improperly installed pads, the air in the lines expand increasing pressure on the pad. bleeding the brakes solves this problem.
How do you reset brake warning light Ford Transit?
The transit brake warning light, on a Ford, can be reset by changing the brake pads. If the warning light is still on after changing the brake pads remove the fuse for 10 seconds.
How do you reset ford transit brake light warning sign?
The transit brake warning light, on a Ford, can be reset by changing the brake pads. If the warning light is still on after changing the brake pads remove the fuse for 10 seconds.
Can you replace back brake pads using front brake pads?
It would be unusual to have the same brake pads front and back. That is not to say it does not happen but normally the brake pads on the driven wheels are bigger than the passive wheels.
Why do you put back the brake clips for brake pads on vw golf?
i replaced brake pads on vw golf and did not put the clips on the brake pads is it save?
