0
The Wheel on your M-30 covers the lug nuts so how do you go about getting this nut cover off to get to the lug nuts?
Wiki User
∙ 17y ago
use a flat head screw driver.
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
Wheel wobble after brake job?
Remove and reinstall the wheel. You do not have the lug nuts installed correctly. The wheel was not seated properly.
When do you recheck the wheel torque?
No need to recheck the torque on the wheel lug nuts of your automobile if they were installed correctly the first time. If you have aftermarket wheels, you should check them with in a hundred miles of instillation.
What is the torque specs for the lug nuts on a 2004 ford ranger 4 wheel drive?
95-105 Ft. lbs.
How do you Replace Wheel Studs on a Drum?
The wheel studs are the main components that hold the wheel tight to the drum. The lug nuts screw onto the front of the wheel studs. When the lug nuts are being tightened, the wheel will compress to the drum. The lug nuts put pressure on the front side of the wheel while the drum puts pressure on the back side of the wheel. Replace the wheel stud immediately if there is cracking or any other type of damage present.Step 1Park the vehicle in a safe location with plenty of working room.Step 2Loosen the lug nuts from the wheel requiring wheel stud replacement with a tire tool.Step 3Jack up the side of the vehicle you are working on with a floor jack and put a car stand under the proper jacking point. Lower the vehicle onto the stand and leave the jack in place.Step 4Unscrew the lug nuts and pull the wheel off. Place the wheel flat so that it does not roll away.Step 5Slide the pry bar between the brake caliper and the brake rotor. Pry the caliper back and forth until the brake caliper becomes loose enough to remove from the side of the rotor.Step 6Unscrew the two mounting bolts from the rear of the brake caliper with a 3/8-inch drive ratchet and a socket. Pull the caliper off of the rotor and hang it to the frame rail or to one of the steering components with a bungee strap.Step 7Tap the drum on the back side with a rubber mallet until the drum is loose. Then, pull the drum off with your hands. If the drum is stuck or very tight, rotate the drum as you are tapping the back side.Step 8Turn the wheel hub so that the wheel studs can be removed from the back side of the wheel hub plate. Put the safety glasses on and hit the wheel stud squarely in the center of the stud with a handheld sledgehammer until it comes out the back side of the hub.Step 9Continue turning the wheel hub and tapping the wheel studs with the sledge hammer until all of the wheels studs are out.Step 10Line the grooves of the new wheel stud up with the grooved holes on the back side of the wheel hub plate. Push the wheel stud into the grooved hole. Hit the head of the wheel stud with the sledgehammer until the head of the wheel stud is completely flush with the back side of the wheel hub plate.Step 11Repeat process with the remaining wheel studs.Step 12Reinstall the brake caliper and the wheel. Tighten both components. Jack the vehicle back up and remove the stand. Lower the vehicle to the ground. Finish tightening the lug nuts with the tire tool until each lug nut stops turning.
How do you remove the steering wheel on a 2001 Dodge Ram truck?
Park the truck with the front wheels in the straight ahead position do not turn or the steering wheel shaft after,before or during or will damage the clockspringDisconnect the negative battery cable and wait at least 2 minutes for the airbag capacitor to discharge before proceedingIf the truck is equipped with speed control remove the switch retaining screws.Pull off the switches and unplug the electrical connectorIf equipped remove the right rear steering wheel cover using a small screwdriverRemove the 4 nuts attaching the airbag module it will probably be necessary to turn the steering wheel to gain access to the nuts; just be sure to center the wheel after the nuts are removedLift off the airbag module and unplug the electrical connector when you set the airbag module down make sure the airbag side is facing up so that if it accidentally deploys it wont launchRemove the steering wheel retaining nut and mark the position of the steering wheel to the shaft if marks don't already exist or don't line upUse a puller to detach the steering wheel from the shaft don't hammer on the shaft to dislodge the wheel
How do you remove the wheel covers from Buick Rendezvous?
You first need to loosen the plastic lug nut covers until they are no longer attached to the wheels lug nuts under the cover. After all five plastic lug nut covers are loosened completely from the lug nuts, you can gently pop the cover from the wheel. If the plastic lug nut covers have been damaged so they are not removable, you will need to get some needle nose pliers and basically break off the plastic lug nut covers. (The plastic lug nut covers keep the wheel cover attached to the wheel. The plastic lug nut covers snap into the wheel cover.) And then the game is on----finding replacement plastic lug nut covers and/or wheel covers......speaking from experience!!!
How do you remove the wheel cover on a Dodge Caravan?
Well, if your vehicle has wheel covers that are held on not only by the spikes that are on the cover, but also by the lug nuts, then you need to look at the cover/cap and see which lug nuts you need to take off in order to get the cap off the rim. alot of the newer vehicles are making the cover/cap so that the lug nuts are helping to hold the cover on the rim and also helps to keep people from stealing the cap. You should only have to take about 2 lugs off in order to get the cover off.
Do the lug nuts hold the wheel cover on a 2002 Ford Taurus?
You can view the 2002 Ford Taurus owners manual online at : www . motorcraft service . com ( no spaces ) Click on Owner Guides ( starting on page 167 it explains if you have wheel covers that are bolted on to loosen the five plastic wheel nuts )
Peugeot 806 wheel bearing how to replace?
To replace wheel bearing on a Peugeot 806, loosen lug nuts and jack the vehicle. Remove lug nuts, the wheel, brake caliper, dust cover, cotter pin, castle nut, and rotor. Unscrew hub nuts of the wheel bearing and replace with new.
How do you remove the wheel covers from a 1995 Honda Civic?
On some cars the covers are held on with the lug nuts. on all hondas from 1986 and newer, if equipped with factory hub caps, they are held on by the lug nuts with black plastic retainer clips.
How do you change the wheel cover in 1999 Ford contour SE?
I belive on Contours they just pop off. Use a screw driver to pry it from the rim. Some cars, use the lug nuts to help hold on the wheel cover. So, before you pry. Look to see if your lug nuts are exposed.(Don't confuse this with fake molded on lug nuts) Then, see if it looks like the wheel cover is between the lug nuts and rim. If not, pry them off. If the cover looks like its held on by the lug nuts you'll have to remove them. You'll have to jack up the car to do this. Just remember to "break" loose the lug nuts before you jack up the car.
How do you remove Camry wheel cover?
If it has a center section that comes out, the lug nuts hold it on. Pop out the center section and the lug nuts are under it. If the face of the cover is solid, you pry it off at the edge of the tire.
How do you change a tire on a Ford Focus?
To change a tire on the Ford Focus, first pry the wheel cover from the center of the wheel. Then, remove the lug nuts from the wheel. Then, using a jack, lift the vehicle so that the wheel that you want to remove is off of the ground. Lift the tire and wheel off of the lug nuts.
What are the two buttons on either side behind the steering wheel for?
if you take buttons off should be nuts behind each one to remove out cover of wheel
How do I remove the wheel covers on a 2001 Hyundai Elantra?
by loosening/removing the lug nuts.. ***CAUTION DO NOT REMOVE LUG NUTS WITHOUT VEHICLE BEING PROPERLY SUPPORTED WITH AN APPROVED SAFETY DEVICE***
What are wheel center caps used for?
According to a google search, it looks like wheel caps are there to cover the lug nuts. Most people use them for the cosmetic appeal however.
Changing the tire on a 2005 AUDI A4?
Loosen the lug nuts counterclockwise. Next, jack up car at the jack points (there are covers below the rocker panels). Jack up car, unloosen all the lug nuts. Remove wheel, replace wheel. Tighten lug nuts until they are seated against the rim. Lower car. Tighten lug nuts crosswise. Next stop, have the lug nuts torqued down.
