Headlamp bulbs are standardized in the industry. That means one bulb will fit a great number of different makes and models. The number is simply the part number used in your car.
its the ref no.
The H in H4 when thinking about a lamp would mean a halogen headlamp. So when stocks people are looking for specific bulbs for their customers they should know to look in the car head lamp section of the store when asked for a bulb starting with the letter "H".
Hi,The headlamp bulb is relatively easy to replace in these vans. What you have to do is remove the turn signal assembly first, and then the headlamp assembly. This is done by removing 3 wing nuts that hold the assemblies in, and then pulling the turn signal assembly straight out, followed by the headlamp assembly. The headlamp assembly has to be lifted UP and then Out.Once you have the assembly out, the headlight bulb can be unscrewed from the back of the assembly and replaced. Be careful not to get any oil from your fingers on the new bulb, as that will heat up when the light is on and decrease the lifetime of the bulb.I have included a link below that shows pictures of the assemblies and how to removed them.Take Care, Greg
Push headlight retaining housing retaining clips (rectangular metal tabs located above radiator wall and to outside and rear or headlight)rearward, then upward to release headlight assembly. Pull headight assembly forward from body. Unscrew bulb retaining ring. Remove bulb from headlight housing. Remove bulb from socket wiring by pulling straight out. Insert new bulb into socket wiring (use paper towel to avoid touching bulb). Reinstall by reversing removal instructions. you also may have to loosen the air filter assembly and remove the air intake flange (rubber part) to gain full access to the screw holding the coolant tank.
No. Ford changed the headlamps and front bumper/grille area for the 2005 model year.
Your best bet is to call your local parts store for prices and part numbers.
Remove the wiring harness from the back of your 1999 Chevy Astro headlamp. Remove the headlamp retaining bolts. The headlamp will come out. Reverse the process to install the new headlamp.
1. Open the hood.2. Remove the thumb screw from the back of the headlamp.3. Release the headlamp retainer by lifting up.4. Pull the headlamp straight forward, to release the ball stud from the grommet.5. Remove the headlamp from the upper fascia support.6. Disconnect the electrical connector from the headlamp.7. Remove the bulb(s) from the headlamp by rotating counterclockwise.8. Release the headlamp trim tabs from the headlamp, if required.9. Remove the headlamp trim from the headlamp, pulling to release the adhesive tape.10. Clean adhesive from the headlamp trim and headlamp using 3M™ adhesive remover P/N 8984, or equivalent.To install:1. Install new adhesive tape 3M® P/N 6382 or equivalent to the headlamp trim, if necessary.2. Position the headlamp trim to the headlamp, if removed.3. Install the headlamp trim to the headlamp, pressing until end tabs are fully seated.4. Install the headlamp bulb(s) to the headlamp by rotating clockwise.5. Connect the electrical connector to the headlamp.6. Position the headlamp to the upper fascia support.7. Press the headlamp into the upper fascia support until the ball stud is fully seated.8. Install the thumb screw to the rear of the headlamp.9. Engage the headlamp vertical retainer, by sliding downward until fully seated.10. Check the headlamp aim, if a new headlamp was installed, or if service or repairs in the front end area were made.11. Close the hood.
It doesn't have a headlamp fuse. They have a circuit breaker built into the headlamp switch.
Open the hood to the engine compartment. Remove the headlamp wiring harness. Remove the headlamp assembly retaining bolts. The headlamp will come out.
How do you remove the headlamp from a Mistubishi Eclipes
1. Open the hood. 2. Remove the front air deflector. 3. Apply light pressure to the headlamp lens to hold the headlamp assembly in place while disconnecting the retainers. 4. Lift up the headlamp assembly retainers to release. Important: Note the location and position of the headlamp adjuster retainers and the locator tab. 5. Remove the headlamp assembly, pulling straight forward from the headlamp mounting panel. 6. Disconnect the wiring harness from the headlamp assembly. 7. Rotate the headlamp bulb/socket counterclockwise to release. 8. Remove the headlamp bulb/socket from the headlamp assembly, if required. There are (2) pull up clip retainers that hold the headlamp assembly in place...Both of these must be removed for the headlamp assembly to be pulled forward...:)
Removal WARNING: The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. NOTE: The headlamp bulb should not be removed from the headlamp until just before a new bulb is installed. Removing the bulb for an extended period of time may effect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamp with the bulb removed from the headlamp. # NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position. Disconnect the headlamp connector. # Remove the headlamp bulb. ## Rotate the headlamp bulb retainer counterclockwise one-eighth turn and remove. ## Remove the headlamp bulb.Installation CAUTION: Bulbs 9004 and 9007 look similar, but are not interchangeable. # Install the headlamp bulb. ## Install the headlamp bulb. ## Rotate the headlamp bulb retainer clockwise one-eighth turn.# Connect the headlamp connector.
Removal WARNING: The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. NOTE: The headlamp bulb should not be removed from the headlamp until just before a new bulb is installed. Removing the bulb for an extended period of time may effect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamp with the bulb removed from the headlamp. # NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position. Disconnect the headlamp connector. # Remove the headlamp bulb. ## Rotate the headlamp bulb retainer counterclockwise one-eighth turn and remove. ## Remove the headlamp bulb.Installation CAUTION: Bulbs 9004 and 9007 look similar, but are not interchangeable. # Install the headlamp bulb. ## Install the headlamp bulb. ## Rotate the headlamp bulb retainer clockwise one-eighth turn.# Connect the headlamp connector.
Remove the air intake splash shield from the vehicle. Remove the 2 headlamp retaining bolts. Remove the lamp assembly from the front of the vehicle. Detach the headlamp connector. Remove the headlamp bulb retaining ring. Remove the headlamp bulb from the headlamp.
The mean is the is the total of the numbers and then dividing by how many numbers.
What does compatible numbers mean?