You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library. Blower motor assembly consists of the motor and impeller. It can provide the airflow when HVAC is turned on. In general, it locates in instrument pannel. rudy jiang jiangyichun@airinter.com.cn
Depends on the vehicle. Many vehicles have the blower motor accessible from under the hood. Others require a lot of stuff to be removed from the interior to get to the blower motor. If you cannot see the motor under the hood sticking out of the heater/AC box you should look at a service manual (factory, Haynes, Chilton...) to see how to do the job.
Blower Motor Resistor: Testing and Inspection Warning: On vehicles equipped with air bags, disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (Ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only way to disable the air bag system. Failure to take the proper pre-cautions could result in accidental air bag deployment and possible personal injury. For circuit descriptions and diagrams, refer to the appropriate wiring information. The wiring information includes wiring diagrams, proper wire and connector repair procedures, further details on wire harness routing and retention, as well as pin-out and location views for the various wire harness connectors, splices and grounds. 1. Disconnect and isolate the battery negative cable. 2. Remove the glove box from the instrument panel. 3. Disconnect the wire harness connector from the blower motor resistor block. 4. Check for continuity between each of the blower motor switch input terminals of the resistor and the resistor output terminal. In each case there should be continuity. If OK, repair the wire harness circuits between the blower motor switch and the blower motor resistor, blower motor or blower motor relay as required. If not OK, replace the faulty blower motor resitor block. How to replace the blower motor resistor block: Caution: Stay clear of the blower motor and resistor block (Hot). Do not operate the blower motor with the resistor block removed. 1. Disconnect and isolate the battery negative cable. 2. Remove the glove box from the instrument panel. 3. Pull out the lock on the blower motor resistor wire harness connector to unlock the connector latch. 4. Depress the latch on the blower motor resistor wire harness connector and disconnect the connector from the resistor. 5. Remove the two screws that secure the blower motor resistor block to the HVAC housing. 6. Remove the resistor block from the HVAC housing. Installation: 1. Position the blower motor resistor block into the HVAC housing. 2. Install the two screws that secure the resistor block to the HVAC housing. Tighten the screws to 2.2 Nm (20 in. lbs.) 3. Connect the wire harness connector to the resistor block. 4. Push in the lock on the blower motor resistor wire harness connecgtor to lock the connector latch. 5. Install the glove box. 6. Reconnect the battery negative cable. 7. Have a nice day!
One would be for the A/C compressor clutch relay, another would be the high speed function for the HVAC blower motor, not sure about the other two.
The HVAC doors that control the airflow are activated by small vacuum motors. The system is designed to fail safe; this means that the system will fail in full defrost mode. So, knowing this and the fact that you have heater but no A/C or defrost you should assume the system has a failed control head (the part that you select functions with with button or lever). Or the doors are stuck due to an warped duct system (usually high heat related).
where is the airconditor drain hose on a 1999 Pontiac Bonneville
The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed without having to remove the instrument panel or the HVAC housing.Disconnect and isolate the negative battery cable.Disconnect the wire harness connector from the blower motor .Release the locking tab that secures the blower motor to the HVAC housing and rotate blower motor counterclockwise.Rotate and tilt the blower motor as needed for clearance to remove the blower motor and wheel from the HVAC housing.
To move air thru the HVAC (heating, ventilation and air conditioning) system.
It should be called the auto HVAC blower motor resistor wire harness. Goes from the auto climate blower motor resistor to the blower motor.
Not knowing what the vehicle is, they are generally found close to the blower motor.
# Disconnect and isolate the negative battery cable. # Disconnect the wire harness connector from the blower motor . # Release the locking tab that secures the blower motor to the HVAC housing and rotate blower motor counterclockwise. # Rotate and tilt the blower motor as needed for clearance to remove the blower motor and wheel from the HVAC housing. also The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed without having to remove the instrument panel or the HVAC housing.
Remove the instrument panel silencer from the passenger side of the instrument panel. Disconnect the wire harness connector from the blower motor. Remove the three screws that secure the blower motor to the HVAC housing. Remove the blower motor from the HVAC housing by rotating and tilting the motor as needed for clearance of the blower wheel....
The blower motor is located in the passengers compartment near the right side of the HVAC module...............
it is just on the outer case of hvac module,and connected with wiring harness and near to the blower motor of hvac
The blower motor is inside the bottom of the hvac housing, under the dash on the passenger side.
Remove the front floor kick-up panel.Remove the cover from the I/P electrical center.Remove the BLO MOT (blower motor) MaxiFuse No. 49 from the I/P electrical center.Remove the right side instrument panel lower insulator panel.Disconnect the blower motor resistor electrical connector from the blower motor.Disconnect the blower motor cooling tube from the HVAC module.Remove the three blower motor retaining screws.Remove the blower motor with fan from the HVAC module.
the blower motor is located on the passenger side of the interior under the glovebox.
where can I find the relay for the hvac blower on a 1995 ford aspire andy