Look for a bulb labeled rough service. You can find them at most hardware stores.
Yes. The bulb will be slightly dimmer, but will last much longer. Most 145V bulbs are intended to be used in 120V exit signs. The reason for the higher voltage rating on the bulb is because it will last a long, long time when used at 120V.
* Newborn: 130 * Older Child: 90-110 * Adult: 50-100* Newborn: 130 * Older Child: 90-110 * Adult: 50-100* Newborn: 130 * Older Child: 90-110 * Adult: 50-100* Newborn: 130 * Older Child: 90-110 * Adult: 50-100* Newborn: 130 * Older Child: 90-110 * Adult: 50-100* Newborn: 130 * Older Child: 90-110 * Adult: 50-100
there are 130 pins
about 130 stock
He'd be 130.
The recommended voltage for 130-volt light bulbs is 130 volts.
130 volt light bulbs have a longer lifespan and are more durable compared to standard voltage bulbs. They are less likely to burn out quickly and can withstand power fluctuations better.
Choose a bulb with the same voltage as your fixture to prevent damage or risk of overheating. If the fixture specifies 120 volts, use a 120-volt bulb. If in doubt, consult the manufacturer's instructions or a professional electrician.
No, it is not recommended to use a 130-volt bulb in a 120-volt socket as it can lead to potential safety hazards. The bulb may burn out prematurely, overheat, or cause damage to the socket and wiring. Always use the recommended voltage bulbs for your light fixtures.
Yes. The bulb will be slightly dimmer, but will last much longer. Most 145V bulbs are intended to be used in 120V exit signs. The reason for the higher voltage rating on the bulb is because it will last a long, long time when used at 120V.
Yes, in fact that is what a rough service bulb is rated at. The bulb used on a 120 volt system will have a reduced wattage output as to what it would be on 130 volts.
It is not recommended to use a 130 volt light bulb in a 120 volt socket as it may cause the bulb to burn out prematurely or even pose a safety hazard. It is best to match the voltage rating of the bulb with the voltage of the socket to ensure proper function and safety.
Yes, because all manufactures figure in a minimal safety factor in order to pass UL code for people who don't follow recommended applications. <<>> A 130 volt bulb will not be as bright as a comparable bulb of the same wattage on 120 volts. Traffic signal light bulbs have a 130 volt rating. Used on 120 volt systems the bulbs last much longer because that are rated for a higher voltage. This bulb will gradually be replaced by LED lamps which have a much more significant life span.
There are not many brass base bulbs left in service these days. This is because aluminium is a cheaper product to use. The 130 volt rating is the maximum voltage that can be applied to the filament. Using this rated bulb on 120 volts will extend the lifetime of the bulb. Many traffic signal fixtures used 130 volt bulbs to cut down on maintenance of changing burnt out bulbs. Today most traffic light have been changed out to LED lamps that get about five times the life of the old incandescent bulbs.
Not a lot. The rating is to denote the voltage the bulb is designed for. The higher rating just says it will handle voltage that high so you have a bit more flexibility if your voltage fluctuates.
It is not recommended to use a 120 volt bulb in a 130 volt socket as it can cause the bulb to burn out faster or even lead to safety hazards. It is important to match the voltage rating of the bulb with the socket for optimal performance and safety.
You're looking at 130v light bulbs? Well...the answer is "nowhere." A 130v light bulb has a heavier-duty filament in it than a 120v bulb does, so the bulb will last longer. Put it in a regular socket and it will work fine.