2 possibilities.
First, if the previous paint wasn't rubber (ie epoxy), it will peel. ...or if this was the first coat, was it primed?
Second and more likely, poor surface prep. Insufficient dry times before and after paint, acid residual, improper paint mixing, etc.
Absolutely not and you should use the same manufacturer of the paint you have on there also. Sorry you can only use a chlorinated rubber base paint on a rubber base paint. If you try to paint with the chlorinated rubber base on top of a synthetic rubber base paint it will probably peel like a bad sunburn.
To determine if a paint chip is epoxy acrylic or chlorinated rubber, you can conduct a solvent test. Apply a small amount of acetone to the chip; if the paint dissolves, it's likely epoxy acrylic. In contrast, chlorinated rubber typically requires a solvent like xylene or toluene to dissolve. Additionally, checking the paint's finish and flexibility can provide clues, as epoxy acrylic is often more rigid, while chlorinated rubber is more flexible.
PPG markets an architectural coating called "Break-Through" that will adhere to rubber and flex without cracking. In addition, there are automotive paints that can be used on rubber, however, they are more expensive.
You can but it wont last, you will have a bigger peeling mess.
I am looking for the same information. Up to this point, the only option the local pool service companies has offered is sand blasting (very expensive).
Absolutely not and you should use the same manufacturer of the paint you have on there also. Sorry you can only use a chlorinated rubber base paint on a rubber base paint. If you try to paint with the chlorinated rubber base on top of a synthetic rubber base paint it will probably peel like a bad sunburn.
To determine if a paint chip is epoxy acrylic or chlorinated rubber, you can conduct a solvent test. Apply a small amount of acetone to the chip; if the paint dissolves, it's likely epoxy acrylic. In contrast, chlorinated rubber typically requires a solvent like xylene or toluene to dissolve. Additionally, checking the paint's finish and flexibility can provide clues, as epoxy acrylic is often more rigid, while chlorinated rubber is more flexible.
either epoxy or chlorinated rubber
The paint may be peeling off the walls in your house due to moisture, poor surface preparation, or using low-quality paint. Moisture can cause the paint to lose adhesion, while inadequate surface preparation can prevent the paint from sticking properly. Using low-quality paint may also lead to peeling.
Peeling paint on walls can occur due to moisture, poor adhesion, or old age. To fix it, the wall should be cleaned, sanded, and primed before applying a new coat of paint. It is important to address the underlying cause to prevent future peeling.
Vinegar can cause paint to break down and lose its adhesion to the surface, leading to peeling or chipping.
Most likely has to do with the VOC levels (amount of volatile solvents in a gallon of paint). Last check is that New York City limits VOC's to 340 grams per liter (around 2.8 lbs per gallon of VOC). Typical chlorinated rubbers are approx 4 to 5 lbs per gallon. In short, too much solvent in the can - solvents evaporate out of the applied film and react with sunlight to form ozone in the lower atmosphere - smog. Chlorinated rubber pool paint IS NOT and HAS NEVER been banned in NY or any other state! The amount of solvents in ALL pool paints have been limited to 340 g/l in NY and many other states. Certain pool paint manufacturers have spread disinformation about chlorinated rubber pool paint being banned, perhaps because they stopped manufacturing it and brought new products to market. Many of the "paint over rubber base" products have failed and those manufacturers are now back into selling rubber base pool paint. Check out www.sausea.com for a company that never abandoned rubber and brought it into VOC compliance as ECO-CHOICE Premium Rubber Pool Coating.
The paint is peeling off the ceiling likely due to moisture, poor adhesion, or age.
To fix paint peeling on a wall, you should first scrape off the peeling paint, sand the area smooth, apply a primer, and then repaint the wall with a fresh coat of paint. Make sure to address any underlying issues causing the peeling, such as moisture or poor adhesion.
PPG markets an architectural coating called "Break-Through" that will adhere to rubber and flex without cracking. In addition, there are automotive paints that can be used on rubber, however, they are more expensive.
You can but it wont last, you will have a bigger peeling mess.
Removing previously applied paint tops gloss paint from peeling of the undercoat on staircase.