0
What else can I help you with?
What do you do if the key is stuck in your Acura Vigor switch?
Replace your ignition lock assembly.
If you lost your key to your moped what would you do to get a new key?
If you lost the key to your moped you will have to contact the manufacturer of the moped to get another key. You can try going to a mechanics shop and see if they have the capabilities of making a new key.
You put the key in to start your 1998 Acura Integra LS but it wouldn't start so you checked the starter plug and pushed it in then the car started but the check engine light came on what does this mean?
You may have knocked off a wire when you reconnected the starter wire, Check the wire going to the O2 sensor. if this isn't it take it to a shop and have them scan the ecm. It could be a flewk.good luck....Michael
What could be wrong with your 96 Integra LS if every time you turn the key to start it clicks then kills all the power in your car but then the power comes back in a few moments?
You need a new battery.
1989 Audi door wont unlock with key?
Will the key turn in the cylinder? i f yes the lock rod inside the door has come off.
How can you find the key code to my 1998 acura integra to replace my lost key?
Call any Acura dealership and give them your VIN Number they should be able to make you a new key but will probably require you to bring ID and proof of registration
Is there a computer chip in the key for a 1990 Acura Integra?
No there is not a Chip in 90 Integra. I have a 91 intergra and made copies at Home Depot
When i stick my key in my 1994 acura integra gsr i have to jiggle the keys sometimes for like 5 minutes before it will let me turn the key?
Worn
How do you pop the trunk when the key doesnt work on a 2000 acura integra?
Most Honda/Acura vehicles have a lever located near the fuel cover release that actuates the trunk release, if it does not fuction it may need to be unlocked using the master key for the car, the valet key will NOT work.
Picture the fuel pump relay located on a 1989 Acura Integra LS?
The fuel pump relay is in the Main Relay attached to the firewall above the foot rest in the drivers foot well. When you turn on the key you should hear a clicking sound, you can feel the relay click if you feel around while turning the key on and off.
Why won't my rear brake light turn off in my 96 acura integra even after I remove key?
When there is erosion in the break light assembly it will do this. The wiring to the break lights may also be grounded out.
How do you test a fuel pump to see if it actually works for a 1992 acura integra gs?
use a fuel pressure guage or get someone to turn the key in the on possition while you listen you will hear it come on
How do you reset maintain require light on 1999 acura integra?
To reset the maintenance required light on a 1999 Acura Integra, turn the ignition key to the "ON" position without starting the engine. Press the gas pedal three times within five seconds. The maintenance light should turn off, indicating that the reset was successful. If it doesn't reset, repeat the process to ensure it's done correctly.
Could any one help me i have changed my starter but now it doesnt even make the usual clicking sound when you tern the key 1995 acura integra?
battery terminal wires not properly hooked up
How do you know if the fuel pump doesn't work on a 1990 acura integra?
you turn your key from one to two one to two and you should here your fuel pump working right by the gas tank let me know if you get it
Where can i find the key code and resistance value of a 1989 camaro rs. lost only key i have?
the dealer can tell your resistance code from the VIN. but with no key to make a copy from, you might have to replace the tumbler then get a key copied.
How do you replace a head gasket on a Acura Integra?
Replacing a head gasket on an Acura Integra involves several key steps: First, disconnect the battery and drain the coolant and oil. Then, remove the intake and exhaust manifolds, timing belt, and cylinder head bolts to lift off the cylinder head. Clean the surfaces thoroughly, place the new head gasket, and reassemble everything in reverse order, ensuring proper torque specifications for the bolts. Finally, refill the coolant and oil, and check for leaks before starting the engine.
