answersLogoWhite

0

1. Rotate spool to line up arrows on spool and surrounding casing. 2. Find notch and pry with wide flat-end screwdriver. 3. Spool will pop out.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How do you load weed eater line on a craftsman?

To load weed eater line on a Craftsman trimmer, first, turn off the trimmer and unplug it if it's electric. Remove the spool from the head by pressing the tabs and pulling it out. Cut a length of trimmer line (typically around 10-15 feet), then insert one end into the spool's eyelet and wind the line in the direction indicated by the arrow on the spool. Finally, replace the spool back into the trimmer head and pull the line to ensure it feeds properly.


How do you change the trimmer line on a Ryobi Expand-It?

To change the trimmer line on a Ryobi Expand-It, first remove the spool cover, then take out the spool and replace the trimmer line following the arrows on the spool. Finally, reassemble the spool cover.


How can I restring a Ryobi string trimmer?

To restring a Ryobi string trimmer, first remove the spool from the trimmer head. Cut a length of new trimmer line, thread it through the holes in the spool, and wind it evenly around the spool. Reinsert the spool into the trimmer head, and feed the line through the trimmer head eyelets. Finally, secure the spool back in place and trim any excess line.


How can I replace a line in a Ryobi trimmer head?

To replace a line in a Ryobi trimmer head, first, remove the spool from the trimmer head. Then, unwind any remaining line and clean the spool. Cut a new piece of trimmer line to the appropriate length and insert it into the spool, following the arrows for the correct winding direction. Finally, reassemble the spool back into the trimmer head.


How do I replace the line on my Ryobi line trimmer?

To replace the line on your Ryobi line trimmer, first, remove the spool cover and take out the spool. Cut a length of new trimmer line, thread it through the holes on the spool, and wind it evenly. Reassemble the spool and cover, and you're ready to trim.


How do I replace the line on my Ryobi gas trimmer?

To replace the line on your Ryobi gas trimmer, first remove the spool cover and take out the old line. Cut a new piece of trimmer line to the appropriate length and insert it into the spool. Wind the line evenly and securely onto the spool, then reassemble the trimmer.


How can I replace the trimmer line on my Ryobi cordless trimmer?

To replace the trimmer line on your Ryobi cordless trimmer, follow these steps: Turn off the trimmer and disconnect the battery. Remove the spool cover by pressing the tabs on the sides and pulling it off. Take out the spool and remove any remaining old line. Cut a new piece of trimmer line to the appropriate length. Insert the line into the spool, following the arrows for the correct winding direction. Reassemble the spool and spool cover, then reconnect the battery and turn on the trimmer.


How can I change the trimmer line on my trimmer?

To change the trimmer line on your trimmer, first, turn off the trimmer and disconnect it from the power source. Remove the spool housing by pressing the tabs on the sides. Take out the old trimmer line spool and replace it with a new one, following the arrows for the direction of the line. Cut the line to the desired length and feed it through the holes in the spool. Finally, reassemble the spool housing and you're ready to trim.


How do I restring a Ryobi gas trimmer?

To restring a Ryobi gas trimmer, first remove the spool from the trimmer head. Cut a length of new trimmer line, usually around 10 feet, and insert one end into the hole in the spool. Wind the line evenly and tightly around the spool in the direction indicated on the spool. Leave a few inches of line unwound, then thread the line through the eyelet on the trimmer head. Reattach the spool to the trimmer head and trim any excess line.


How do I reload the line on my Ryobi string trimmer?

To reload the line on your Ryobi string trimmer, first remove the spool from the trimmer head. Cut a length of new trimmer line, usually around 10 feet, and insert one end into the spool's center hole. Wind the line evenly and tightly around the spool in the direction indicated on the spool. Leave a few inches of line unwound, then thread the line through the trimmer head's eyelet. Reassemble the spool onto the trimmer head, ensuring the line feeds through the head properly.


How do I load the Ryobi trimmer head?

To load the Ryobi trimmer head, first remove the spool cover and line up the arrows on the spool with the eyelets on the trimmer head. Insert the line into the eyelets and wind it in the direction indicated on the spool. Make sure the line is secure and replace the spool cover.


How do you wind a Ryobi weed wacker spool?

To wind a Ryobi weed wacker spool, first remove the spool from the trimmer. Then, wind the trimmer line around the spool in the direction indicated on the spool. Make sure to evenly distribute the line and avoid overlapping. Finally, reattach the spool to the trimmer and you're ready to use it.