The cover and mirror assembly is connected by 2 plastic pins located behind the light lenses and a clip at the bottom. Gently pop off the complete assembly to access the lights or to replace cover. Caution should be used when removing as the mirror is only held in place by the door clips and the bottom plastic trim may easily snap. Pulling the assembly from the sides about 1/3 down from the top should cause the pins to snap out. Re- assembly is easy, simply align pins and apply pressure until the cover snaps in place. Then snap bottom clips in place applying pressure near the bottom of the light lenses. GM wants to sell you a complete visor assembly for $360 but found the parts I needed on line for about $30
To change the vanity mirror light bulbs in a 2004 Mercedes, first, gently pry off the plastic cover of the vanity mirror using a flat tool or your fingers. Once the cover is off, carefully remove the old bulb by pulling it straight out. Insert the new bulb in the same socket, ensuring it's securely in place, and then snap the cover back onto the mirror. Finally, test the light to ensure it’s working properly.
To replace a mirror on a Citroën Saxo, first, carefully pry off the mirror cover if applicable. Then, use a screwdriver to remove the screws securing the mirror to the door. Disconnect the electrical connector if the mirror is powered, and then detach the mirror from the door. Attach the new mirror by reversing the steps: connect the electrical plug, secure it with screws, and replace the cover.
www.sunvisordepot.com.they are great!
To remove and replace the driver-side mirror on a 2001 Toyota Camry, start by carefully prying off the plastic cover at the base of the mirror to expose the mounting screws. Use a socket wrench to remove the screws securing the mirror to the door. Disconnect the electrical connector if your mirror is powered, then pull the mirror off. To install the new mirror, reverse the process: connect the electrical plug, secure the mirror with screws, and replace the plastic cover.
if the frame of the mirror is still there, then buy a mirror that sticks on and cover the broken mirror. buy this at auto store or bigger retail stores.
* Remove the mirror trim cover from the door panel * Remove the three mirror retaining nuts and detach the mirror from the car
To replace the driver's side mirror on the 2003 GMC Envoy, first remove the interior door panel. Then, remove the mirror connection cover inside the panel as well. Unscrew the screws holding the mirror to the door. Remove the wiring and replace the mirror with a new mirror. Replace the screws and place the door panel back onto the door.
To replace the rearview mirror on a 2001 Honda Prelude, start by gently prying off any plastic cover that conceals the mounting bracket. Use a screwdriver to remove the screws holding the mirror in place, then slide the old mirror off the mounting bracket. Align the new mirror with the bracket, secure it by tightening the screws, and replace any plastic cover if applicable. Finally, adjust the mirror to your preferred angle.
To replace a door mirror on a Citroën C5, first, ensure the vehicle is turned off and the keys are removed. Carefully pry off the mirror's plastic cover to access the mounting screws, then unscrew and disconnect the electrical connector if the mirror is powered. Remove the old mirror and replace it with the new one, reconnecting the electrical connector and securing it with screws. Finally, snap the plastic cover back into place and test the mirror for proper function.
To replace a door mirror on a Renault Laguna, start by carefully prying off the cover panel on the inside of the door to access the mirror's mounting screws. Remove the screws securing the mirror to the door frame, then disconnect the electrical connector if it’s a powered mirror. After removing the old mirror, position the new one in place, reconnect the electrical connector, and secure it with the screws. Finally, replace the cover panel to complete the installation.
To replace a mirror in a Toyota vehicle, first, the negative cable of the battery should be disconnected. Then, the mirror cover should be removed from the door panel carefully, and the wiring disconnected so the mirror can be replaced.
To replace the rearview mirror in a 1999 Acura RL, first, remove the plastic cover at the base of the mirror by gently prying it off. Next, unscrew the mirror from its mount using a Phillips screwdriver. Install the new mirror by aligning it with the mount and securing it with the screw. Finally, reattach the plastic cover for a finished look.