0
Assuming there is 8 wires in existing Renault wiring iso speaker plug at back of radio, the two outer wires at each end of plug are for left rear and right rear speakers, tap into these wires i.e. strip the insulation back a couple of inches from the plug and join new speaker wires onto the stripped wires.
If only 4 wires in existing Renault wiring iso speaker plug then buy iso speaker plug from auto factor and join existing Renault wiring on speaker plug onto new cable and join new speaker cables (the ones you are fitting) onto the outside wires at each end of the new iso plug.
What else can I help you with?
How do you fit 6 by 9 in a peugeot 106?
you need to start by fitting them into the parcell shelf, run the cables under the back seats and then under the carpet on the passenger side. there is a slight gap in the side of the head unit slot and behind the glove box to run the cables through. on the ISO cable from your head unit there should be 4 cables that arn't on the other side of the connection, these are your speaker outputs that you need to snip and connect to your speaker cables, making sure you connect the positive with the positive and the nagative with the negative.
Should your speakers be plugged into a head unit when using a speaker amp?
No
What is a line level?
i am on my way to figuring this one out myself. im using this in car audio terms though. it converts the regular speaker wires, like the ones that come out of the back of a car stereo head unit, into rca cables, so you can plug them into an amp. rca cables are the ones that look like xbox or playstation video cables, except its only audio
How do you connect an Amp and sub to your kenwood head unit?
To connect an amp and sub to your Kenwood head unit, first ensure you have the necessary RCA cables, speaker wires, and power connections. Connect the RCA outputs from the head unit to the inputs on the amplifier. Then, wire the subwoofer to the amplifier according to the sub's specifications. Finally, connect the amplifier to the car's power supply, ground it properly, and ensure all connections are secure before powering on.
What is a line level converter?
i am on my way to figuring this one out myself. im using this in car audio terms though. it converts the regular speaker wires, like the ones that come out of the back of a car stereo head unit, into rca cables, so you can plug them into an amp. rca cables are the ones that look like xbox or playstation video cables, except its only audio
Do you have to bypass a factory amp in a 2002 Chevy sub?
U run you own set of speaker wire from head unit to each speaker
Are all sub woofer cables universal?
The simple answer, is NO. It depends on the actual connection. From the head unit to the amplifier, it typically is an RCA cable, but if your using "Speaker level inputs" then it would be speaker wire. (with a special harness). However, if your hooking up a Subwoofer to an Amplifier, depending on the guage of wire, Yes. They are universal. Many people typically just use plain speaker wire, however, many use special "Shielded" wire for subwoofers.
How do you connect a sub woofer to a head unit without a RCA input?
To connect a subwoofer to a head unit without RCA inputs, you can use a high-level (speaker-level) input adapter, which converts the speaker wire signal from the head unit into a signal suitable for the subwoofer. Alternatively, you can use a line output converter (LOC) that attaches to the speaker wires, allowing you to create RCA outputs for the subwoofer. Once connected, adjust the gain and crossover settings on the subwoofer or amplifier to ensure optimal sound quality.
Where is flasher unit in a Renault clio 2003?
The flasher unit is intergrated within the instrument panel
Can you change the head unit on a Mazda Rx8?
it is not practical to change the head unit on a RX8 The above answer is correct. There are many ways to make an after market head unit "fit" into the RX8, but you will probably lose the steering wheel stereo controls. You can connect aftermarket amplifiers to the stock head units speaker output and use aftermarket speakers. Get the MP3/CDROM addition for the stock CDROM head unit from a Mazda dealer.
Why does your car amplifier have inputs and outputs?
It has inputs and outputs because an amplifier is a power source and has an audio signal going in to it from the head unit using audio cables(input) and then the signal goes out through the speaker wires(output).
What is a guitar amp head and how does it differ from a combo amp?
A guitar amp head is the part of an amplifier that contains the electronic components that amplify the signal from the guitar. It needs to be connected to a separate speaker cabinet to produce sound. A combo amp, on the other hand, combines the amp head and speaker in one unit.
