0
This procedure applies for both 194, 230 & 250cui engines. 1. Clean the intake manifold using 200 grit emery cloth until metal is shiny. 2. Locate carb. gaskets, use high temp silicone (red) and apply a thin coating on the manifold suface. Install gasket on to mainfold. 3. Clean both sides heat shield plate which acts as a heat deflector for the carb using the same emery cloth in 1. above. Clean only the surfaces of the plate which mate to the manifold. 4. Apply thin layer of silicone as in 2 above. to the mating surface of the heat shield meeting the surface of the gasket installed in 2. 5. Install the heat shield. If the unit is fitted with an automatic choke, feed the choke rod through the hole of the heat shield. This rod will connnet to the butterfly choke valve at the top of the throat of the carb. 6. Another gasket is required between the heat shield and the carb. Apply silicone to both sides of the second gasket, and install to the heat shield. 7. Install the carb. Bolt the carb using 25 ft-lbs of torque. 8. Connect throttle linkage to the carb. Operate and check the throttle for full range of motion. 9. Connect the vacuum advance hose coming from the distributor vacuum advance unit to the base of the carb. Typically this doesn't need a clamp depending on the fit and size of hose. 10. Connect the fuel line to the carb. Clamp using small pipe clamp or equivalent. 11. Connect the choke rod to the butterfly valve as described in 5. above. 12. Install the air cleaner horn and air filter. 13. Install the air cleaner horn cover using a wingnut. (no not your neighbour :-) 14. Get in the car, crank it over and pump the sh-t out of it until it starts. 15. Peel out if you've got the power.
What else can I help you with?
Where is the fuel filter located on a 1978 Chevrolet Nova?
Remove the fuel line from the carburetor using a 5/8 and a 1 inch wrench. With the 1 inch wrench remove the fitting from the carburetor. Install the new filter with the spring first.jd
What carburetor came on a non SS 1971 nova with a 350?
It was a 4 barrel Rochester ( Quadrajet ) Carburetor.
What is the difference between a 1965 nova and a 1965 nova ss?
heavier duty suspension, gauges, badging, ETC.
How much to pay for a 1965 nova?
how much would you pay for 1965 Chevy nova 6cyl in good shape
Did the 1965 impala 327 have a 2 barrel carburetor?
My father has a early 65 with a 4 barrel carburetor.
When was Nova - UK magazine - created?
Nova - UK magazine - was created in 1965.
How do you rebuild a carburetor on a 1976 Chevy Nova?
get a rebuild kit for your model carb and follow the directions.
Where can you find a 1965 ford carburetor diagram?
Where do the ball checks & accelerating pump discharge weight go on the lower body of a 1- v carburetor for 1965 mustang 6cyl with automatic transmission
Will a 1962 Chevy nova grille fit a 1965 Chevy nova?
Not really. There is a difference between the headlight rings.
When was Nova Color Artists Acrylic Paint created?
Nova Color Artists Acrylic Paint was created in 1965.
How do you install a carburetor 1988 mighty max?
To install a carburetor on a 1988 Mitsubishi Mighty Max, start by disconnecting the battery and removing any necessary components such as the air intake and throttle linkage to access the carburetor. Carefully unbolt and remove the old carburetor, ensuring to clean the mounting surface on the intake manifold. Install the new carburetor by aligning it with the mounting holes, tightening the bolts securely, and reconnecting all hoses and linkages. Finally, reconnect the battery and check for any fuel leaks before starting the engine.
How do you install a chock on Rochester carburetor?
To install a choke on a Rochester carburetor, first ensure the carburetor is clean and the engine is off. Remove the air cleaner and locate the choke housing on the carburetor. Position the choke plate within the housing and secure it with screws, ensuring the spring is properly oriented. Finally, connect the choke linkage to the throttle lever and adjust it as necessary for proper operation.
