answersLogoWhite

0

there is a connector under the dash that is used for the computer called an OBD 2 connector. It is rectangle in shape, about 1 1/2 inches long. More than likely you will have to unbolt this. When unbolted, find the numbers on the connector. It should be numbered 1-8 on the top and 9-16 on the bottom(nombers are very hard to see.) You will need to jump pin #4 and #8 with a wire or paper clip. Turn the key on. (some GM models you do not have to have the key on.) The locks will cycle automatically. Once the locks cycle, push the unlock and lock buttons on the key fob within 10 seconds and hold until locks cycle again. Once locks cycle, release and fob should be programmed.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

A 1994 Monte Carlo won't respond to reprogramming of the fob - What might be the problem?

Because Monte Carlo is a Biscuit and it would be rather stale if its from 1994... fool!!!


What are the numbers on the back of the remote that I need for my 97 Monte Carlo Ls key fob?

In most cases if you call your local Chevrolet dealer, give the parts dept. your VIN (Vehicle Identification Number) you can order a key fob for that car.


How do you program the 2007 Monte Carlo key fob?

If this a new fob that has never been programmed before you will need to go to the dealership to have it done. If it's one that quit working & you've had to replace the battery in , stand next to the car and depress the lock & unlock buttons at the same time,it may take 15-20 seconds for this to work,but when it does the headlights will flash on then off.


What causes the security light on the dash of a 2003 Chevy Monte Carlo go on?

The problem with the Monte Carlo is in the Security system itself I own a 2001 SS and it use to do the same thing. The security system does not recognize the key, when you use the key pad to enter the car. The only way I got it to work correctly was to Stop using my key FOB (remote). If you have the problem where your vehicle will not start, Get out, put the key in the door with it closed and turn the key to unlock for 10 seconds. It tells the car that the key was used to open the door not the key FOB. Monte Lover.


How do you program key fob on 1996 xk8?

To program the key fob for a 1996 Jaguar XK8, first, insert the key into the ignition and turn it to the "On" position without starting the engine. Within five seconds, press and hold the "Lock" button on the key fob for about 10 seconds. Release the button, turn the ignition off, and then turn it back to the "On" position. Repeat this process for any additional fobs. Ensure the battery in the fob is fresh to ensure proper programming.


How do you program a key fob to a 2006 Chevy Malibu?

How do you program a key fob to a 2003 Chevy Malibu


How do you program a 1995 Lumina APV key fob?

To program any kind of key fob you have to take it to a dealership.


Reprogramme a remote fob for Ford maverick?

code for maverick 1996 fob


How do you re program key fob for Renault laguna1997?

How do I re program my key fob for renault laguna estate 1997?


Why a 2003 Monte Carlo wouldn't start or even turn over after drivingbut dash lights radio and gauges flickered on and off?

When my 2003 Monte did that it was a bad connection to the battery. It got just enough power to think it was being stolen and my key fob stopped working. Once I cleaned up the battery contacts it was fine.


How do you program a 2003 deville with a new key fob?

You don't. Take the car and the new fob to a caddy dealer or a locksmith who has the equipment to program it.


How do you program new key fob 2006 Chrysler town and country?

A scan tool is required to program a fob on a 2006 Chrysler Town and Country.