0
The rear bumper cover is fastened to the car in exactly 9 places. Follow this procedure:
- Raise the trunk lid
- Remove the three push-in fasteners in the center of the top of the bumper, directly underneath where the license plate holder would be when the trunk lid is closed
- Jack up the car and remove the driver's rear wheel << you don't *have* to do this. You *can* do the rest without doing this, but your life will be easier if you do. Trust me.
- On the driver's side, at the bottom rear of the rear wheel well, remove the two screws that attach the bumper cover to the rear fender
- Peel back the wheel well liner (very stiff piece of black plastic). Remove the hidden screw attaching the bumper cover to the fender. This screw is approx 2 inches from the forward edge of the bumper cover.
- Repeat for the passenger side
- Bumper cover should simply fall off.
What else can I help you with?
How do you remove remove rear bumper Chrysler sebring 2004 touring?
To remove the rear bumper from a 2004 Chrysler Sebring Touring, start by opening the trunk and removing any screws or clips securing the bumper to the body. Next, detach the tail lights by removing the screws and gently pulling them out. Then, locate the bolts underneath the bumper and on the sides, typically near the wheel wells, and remove them. Finally, carefully pull the bumper away from the vehicle, ensuring any remaining clips are released.
2008 rear bumper Chrysler Sebring how to take it off?
To remove the rear bumper from a 2008 Chrysler Sebring, start by disconnecting the negative battery cable for safety. Then, remove any screws or bolts securing the bumper, which are typically located under the rear lights and along the underside of the bumper. Carefully detach the clips or fasteners holding the bumper in place, and gently pull the bumper away from the vehicle. Finally, disconnect any electrical connectors for rear lights if applicable before fully removing the bumper.
Can you use a front bumper from a 96' Mitsubishi eclipse or Chysler sebring for my 96' Dodge avenger?
You can use the front bumper for a 1996 Chrysler Sebring on a 1996 Dodge Avenger.
What is the factory warranty for a 2008 chrysler sebring?
The bumper to bumper warranty was 3 years 36,000 miles.
Where is the battery on a 2005 Chrysler sebring convertible?
I have a 2001 sebring and they tend to place the battery in the front driver fender area. You have to remove the front driver tire, then remove (pry or unscrew) the bolts that hold the fender shield in place. It's most likely there in the fender/ bumper area.
Where is the car horn in 2010 sebring?
In the 2010 Chrysler Sebring, the car horn is located behind the front grille, typically near the center of the vehicle. It is mounted on or near the front bumper support. To access it for repairs or replacement, you may need to remove the grille or parts of the front assembly.
How do you remove the passat rear bumper?
how to remove 2013 passat rear bumper
How do you remove the front bumper from a 2002 Hyundai Santa Fe?
Remove the screws in the wheel wells and underneath the plastic cover to remove the bumper cover. Then you can see to remove the actual bumper.
How do you remove a citroen berlingo front bumper?
how to remove front bumper on citroen berlingo
How do you remove front bumper on 2002 impala?
how to remove front bumper 2002 Impala
How do you remove the rear bumper on a 2004 Nissan Sentra?
To remove the rear bumper on the 2005 Nissan Sentra, you will first need to remove the rear bumper cover by using a flat tool to pry the pins. Then, access the bolts holding the bumper to the frame of the vehicle and remove the nuts. The bumper will then lift off.
How do you remove a bumper from a 1998 Nissan altima?
How to remove the front bumper to a 1998 Nissan Altima?
