0
We need a few more details, but I can make a few assumptions.
If this is an in-ground pool, and you have a standard pool light that is mounted in a niche that was installed in the sidewall of the pool, and you are replacing the bulb, then you should do the following:
First and foremost, turn off the breaker switch that supplies the current to the pool light.
On the rim around the light, you should find a screw (usually at the top of the trim ring) - unscrew this screw and the fixture should tilt out of the niche and literally float to the surface of the pool (there should be enough electric cable to allow the fixture to float up and be placed on the pool deck).
Depending on the fixture model, you will now need to remove the glass - some will have several screws on the back side that screw into the trim ring, and some may have a clamp that incorporates the glass lense and clamps around the fixture. Both will involve a rubber seal, and it is a good idea to replace this seal at the same time the bulb is replaced - many pool supply shops or on-line stores will have this seal available, and if you have the model number of the fixture, it should be easy to locate.
Once you open the fixture, inspect for any signs of water intrusion - this is possible if the seal has hardened. Remove the bulb, and inspect the socket for any corrosion - clean as necessary.
Replace the bulb, install the new seal, tighten the seal clamp or the rear clamp ring to make sure the fixture is water tight. You could turn the power on the lamp BUT only for a second to make sure the lamp is good and rule out any issues with the fixture - IMPORTANT - Pool lamps should only be operated when installed in the pool to prevent heat build-up.
If all is good, turn off the power at the circuit breaker; place the fixture back in the pool, loosely coil the excess power cable around the fixture, and install the fixture back into the niche. Line up any tabs that secure the fixture in the niche, and tighten the mounting screw. Turn on power, and test.
What else can I help you with?
How do you change the lite in an in ground pool?
Turn of the breaker to the light. Drain the pool (at least below the light). Unseal the light. Remove and replace the bulb. Re-seal the light (replace the gasket if the mfr recommends this). Turn on the breaker and check the light for function. Fill the pool. Check the light for leaks. Piece of cake, actually. It just takes a while to do. Don't forget to check the pool chemistry after filling it!
What could be wrong if your swimming pool light goes on by itself?
You probably need to replace the light switch
How to Replace 120 volt pool light with a 12 volt pool light?
To replace a 120 volt pool light with a 12 volt pool light, you will need to ensure that the new light is compatible with your pool's existing wiring and transformer. Consult the manufacturer's instructions for the specific installation steps. It is recommended to hire a professional electrician to safely make this switch.
How can I replace pool table lights?
Some sporting good shops like Big 5 may offer good deals on new pool table lights or they may also sell parts to replace the broken pool table light.
How do you remove damaged screws from an underwater pool light?
If the light is really old or been subject to chemical abuse by the pool water then you will probably have to replace the light. If the light is in good shape you can get a screw extractor from the hardware store just be careful not to strip the threads out!
How do you replace the light fixture on an in ground swimming pool that doesnt have enough cord to bring it out of the pool?
The whole fixture should be replaced and the new one installed properly. There should be enough cord wrapped around the light in the niche to bring it up to the pool deck. You could drain the pool down, but I don't recommend it. When I see this condition, I don't take chances, I replace the whole light, cord, etc. Its not something to fool around with if you don't know what your doing. A: Call a qualified swimming pool electrician. He will bring the pool light and all related items to the light fixture up to code. This is not a job for an ammature.
How do you replace 120 volt pool light with a 12 volt pool light?
Answer for countries in Europe and other world areas running a 50 Hz power supply service. This depends on the the light or globe, if you can replace just the globe its very simple. change over the globe and buy yourself a mains(230v or 115v) to 12v isolation transformer, and attach that to the mains cable and run a cable from the 12v to the globe and away you go. The description of how to change the mains to 12v is the same if you have to replace the whole light. Then you just have to replace the globe or the whole light assembly.
Does the gasket for a pool light fixture also hold the housing ring on?
The housing ring, depending on brand, will hold the gasket. Some lights are assembled with a housing ring and screws others have a clamp type ring. There are several types manufactured. Remember to always replace the gasket with a new one when replacing the bulb etc. Ken
Could lightning damage a pool light?
Yes, lightning can damage a pool light.
If you have just leased a home and cannot find the switch to turn on the pool light how can you trace it?
Pool lightCall the company or person that leased you the property and ask them where the switch is to the pool light. If they don't know; often a pool light is turned on by a breaker in the panel marked "pool light." A breaker is an overcurrent protective device, it can not be used to "switch" a light unless it is marked "SWD".
Can you replace the main drain in concert pool?
no you can not
Pool Liner?
form_title= Pool Liner form_header= Replace or install a liner for your pool. Do you need to replace an existing liner?*= () Yes () No Is it an in-ground or above-ground pool?*= () In Ground () Above Ground What is the size of your pool?*= _ [50]
