0
To respool line on a Craftsman 17" 25cc weedwacker, first, unplug the spark plug for safety. Remove the spool from the trimmer head by pressing the tabs and pulling it out. Wind the new line onto the spool in the direction indicated, leaving a few inches free at each end. Finally, reinsert the spool into the head, ensuring the line is properly threaded through the eyelets, and reattach the trimmer head.
What else can I help you with?
Why is the gas not going in the prime bulb of a Craftsman 25cc Gasoline Weedwacker?
If the bulb is cracked or the line going to it is it will not work, also make sure the hose going to it is submerged in the fuel. another possibility is that the vent hose is plugged and the tank has too much vacuum pressure to allow the fuel to be sucked up.
What size line does craftsman 17 25cc weed wacker take?
1/8" feed line 3/16" return line.
What is fuel line diagram for Craftsman Weedwacker 32 cc?
Diagram showing where the lines from the fuel tank go at the carburetor and the primmer bulb.
Gas line connection for a Sears model 358 798420 weedwacker?
To connect the gas line for a Sears model 358.798420 weedwacker, first ensure the engine is off and cool. Locate the fuel lines, typically one leading from the fuel tank to the carburetor and another returning to the tank. Attach the fuel line securely to the carburetor inlet and ensure the return line is connected properly to avoid leaks. Always check for any kinks or obstructions before starting the engine.
What is the oil to gas ratio for a craftsman 17 25cc weedwacker?
If it was made in the last five years or so, it should be 50 to 1. The above answer is incorrect for my Weedwacker. Craftsman Weedwacker 17"/25cc Gas Line Trimmer 2003 US EPA PH2 Family: 3PWES.0254TZ Disp: 25cc : EM Serial: [redacted] Model: 358.795543 Emission: durability period 50 hours Customer questions: 1-800-235-5878 IMPORTANT! Mix CRAFTSMAN 40:1 2-cycle engine oil with unleaded gasoline. Read oil container or operator's manual for proper mixing instructions. Other oils may cause engine damage. 1. Place stop switch in "ON" position. 2. Set unit on flat surface. 3. Slowly press the primer bulb 6 times. 4. Move choke lever to "FULL CHOKE" position. 5. Squeeze throttle trigger fully and hold [thru step 6] and pull starter handle sharply until engine attempts to run. NO MORE THAN 6 PULLS. 6. Move choke lever to "HALF CHOKE" position and pull starter handle until engine runs. 7. Allow engine to run for 10 seconds, then move choke lever to the "OFF CHOKE" position. TO STOP ENGINE MOVE STOP SWITCH TO "OFF" POSITION. The above three paragraphs are verbatim from three stickers on my Weedwacker. The stickers have no copyright on them. The simple answer to your question is, "40:1 2-cycle engine oil with unleaded gasoline." rcpao 2008-06-29 22:03
How do you change the spool on a craftsman weedwacker model 257796022?
To change the spool on a Craftsman Weedwacker model 257796022, first, make sure the trimmer is turned off and unplugged or the battery is removed. Press the tabs on the spool cover to release it, then carefully remove the old spool. Install the new spool by threading the line through the eyelets, then replace the cover, ensuring it clicks securely into place. Finally, wind any excess line if necessary and you're ready to go.
How do you untangle the line on a kid's Zebco fishing pole?
Theres a reason they sell spare spools of line. Its easier to cut away the rats nest and pull out more line or respool the reel with new line that trying to fight that dilemma. The quality of line used on those combos isn't the greatest to begin with. Trilene 6 or 8 pound test is more than enough for that type rod and fishing conditions.
How do you attach fuel line on Craftsman Weedwacker model 358.797150?
drain the fuel, remove the fuel filter from inside the tank, remove the old fuel line from the filter, remove the old fuel line from the carb, pull old fuel line out, install new fuel line through the tank, reconnect fuel filter to new fuel line, place filter and slack line into tank, connect new fuel line to carb, refill tank, check for leaks.
If you have a Craftsman 32cc Weedwacker and the fuel line from the tank element to the carb has fallen apart and the element filter is lose in the fuel tank - How do you go about fixing this?
Dump all of the fuel out of the tank. Then take a pair of long needle nose pliers and grab the end f the fuel line. Inspect it for swelling or complete disentegration. The ethanol added to gas that is now mandatory in many states is very tough on fuel line. You may have to replace the fuel line and put a new fuel filter on while you're at it. Patience is a virtue.
What is the oil to gas ratio on craftsman 32cc weedwacker?
40:1 is the correct mixture for the fuel and 2 cycle oil. 3 oz. of 2 cycle oil per gallon of gas. I have Craftsman Line Trimmer 358.795190 (Model #). It has the quick release shaft for other attachments. Hopefully this will help you.
How do you hook up gas lines for craftsman weedwacker model no 316 798221?
The process will vary between models. The lines should be fit into the tank tightly, with no gaskets. There may be an internal filter in the tank, it plugs on the end of the suction line. The other ends of the lines slide tightly onto the carburetor fittings.
What is a miter line used for?
A miter line is used in woodworking and construction to create precise angles, typically at 45 degrees, for joining two pieces of material, such as in frame corners or moldings. It serves as a guide for cutting, ensuring that the edges fit together seamlessly. By marking a miter line on the workpiece, craftsmen can achieve clean, accurate cuts that enhance the overall appearance and structural integrity of the finished product.
