0
Since I do not know what kind of machine you have ( you can sometimes look for the manufacturers website, and see if they show a threading diagram ) all I can say is the rule of thumb is to draw the thread from the spool, usually, through a disc or eyelet, and draw the thread down a slot, ( it will catch a hook of some sort, inside that slot ) then back up, usually passing between 2 discs, ( which hold the tension ) over another hook ( this is an obvious slot in the thread take up ) and back down to the thread guide and to the needle.
You will always have the thread moving down, up then down again, for a total of 3 passes through the mechanism. MOST machines are threaded from left to right, though I had one machine that threaded from right to left.
Like I said, it might be a good idea to check the manufacturers website for threading instructions.
What else can I help you with?
To use a needle and cotton?
Thread the cotton through the eye of the needle, leaving a tail to hold onto. Hold the needle steady and start sewing by pushing the needle in and out of the fabric. Remember to knot the thread at the end to secure your stitches.
What does the needle do in a sewing machine?
Pushes thread through fabric to make stitches.
Feeds thread from spool to needle?
The thread moves from the spool through the needle to make stitches on a sewing machine. The thread take-up lever is what feeds the thread from the spool to the needle as it moves up and down.
How do you thread a Jones vx760?
To thread a Jones VX760 sewing machine, first, ensure the machine is powered off. Begin by raising the presser foot and placing the spool of thread on the spool pin. Then, guide the thread through the tension mechanism, following the threading path indicated on the machine, and thread the needle from front to back. Finally, pull a length of thread through the needle and lower the presser foot to complete the setup.
What is a thread machine?
its a cotton gin
What does the thread guide do on the sewing machine?
The thread guide keeps the thread running in the proper place. If the thread is not threaded correctly, the tension will be off, resulting in jammed or broken threads in the machine.On a sewing machine, the thread guide is a small part that is attached above the needle. It looks like a hook and it hold the thread in place as it is fed through the needle.
What is a thread path on a sewing machine?
Thread is the name for the string used in sewing. It is usually very thin, so that it is easily put through the eye of a needle and pulled through fabric. It is sold in many colors, and in many different weights.
Which hand powered machine helped turn cotton into thread?
It was the Spinning Jenny that changed cotton into thread. The cotton gin removed the seeds.
What tools can you use for sewing?
Needle and thread. Sewing machine.
How to pass thread through the eye of a needle unaided?
Pass a thread through the eye of a needle unaided from the opposite side of the needle towards the human eye; while looking through the eye of the needle.
How do you use a knitting machine?
to use a knitting machine for the girls only one you have to thread it on one needle and then not thread it on to the next then thread it on again then don't etc
How do you thread a universal sewing machine model kat?
The thread must come from the FRONT of the upright spool on the back of the machine. Thread through the small eyelet on the back (nearest the spool(s), projecting from the top), then through the thread guide at the front of the machine. If you are using a double needle (therefore two spools of thread), the thread from the left-hand spool should go through the top hole and the thread from the right-hand spool through the bottom hole. Come down to the tension disks. Bring the thread through the back disk, up again under the wire guide, and down under the thread guide that is just to the left of the tension disks. Bring the thread through the eye of the take-up lever (the piece that moves up and down when you sew) from RIGHT to LEFT. Guide the thread back down through the thread guide next to the tensioner. There is a little thread guide just inside the door on the left side of the machine; bring the thread through this guide. Then pull the thread through the wire guide above the needle (it's easiest to hold the thread horizontally to do this). Thread the needle front to back. HTH. YMMV.
