puch top of clip in and slightly to the left, it will then unclip and hinge downwards, releasing the bulb.
Not at all...press in (together) and it pops off.
on the peugeot 205 the headlight can be fitted / removed as follows; lift the bonnet the headlight assembly is held in place by 2 springs on the sides unclip each spring there is a slotted grub screw above the lamp that adjusts the angle of the lamp slacken off this screw (counter clockwise) you will find that the connecting rod is fitted using a small ball joint. unclip the ball joint and the lamp will then release. the wiring connections to each bulb are a simple spade type push fit.
Just look at it closely...push in, squeeze...releases Not a good answer, you smug SOB.... This is the most ill conceived POS I have ever run into,
To replace a headlight bulb in a Nissan Micra, open the hood, locate the back of the headlight, disconnect the electrical connector, remove the rubber cover, unclip the bulb retainer, remove the old bulb, insert the new bulb, and reassemble in reverse order, making sure to test the high and low beams. Here's a more detailed breakdown: Preparation: Open the hood: Locate the back of the headlight assembly in the engine bay. Turn off the car: Ensure the car is off and the headlights are not on. Accessing the Bulb: Locate the back of the headlight: Find the back of the headlight assembly. Disconnect the electrical connector: Gently pull off the electrical connector from the back of the bulb. Remove the rubber cover: Locate and remove the rubber cover that surrounds the bulb housing. Removing the Old Bulb: Locate the bulb retainer: Find the spring clip or retainer that secures the bulb in place. Unclip the retainer: Squeeze the retainer and unclip it to allow access to the bulb. Carefully remove the old bulb: Grasp the bulb and carefully pull it out of the housing. Installing the New Bulb: Insert the new bulb: Align the new bulb with the housing and insert it, ensuring it's properly seated. Replace the bulb retainer: Secure the new bulb in place by clipping the retainer back into place. Replace the rubber cover: Put the rubber cover back on the bulb housing. Reconnect the electrical connector: Plug the electrical connector back onto the bulb. Testing and Final Steps: Test the headlights: Turn on the car and test both the high and low beams to ensure the new bulb is working correctly. Close the hood: Make sure the hood is properly closed. This video demonstrates how to replace a headlight bulb on a Nissan Micra: 51s DIY Car Maintenance and Repair Guide YouTube · 9 Jan 2014
There is a plastic cover that screws into the headlight housing turn it anti-clockwise to reveal ur h/l bulb. Remove the plug 1st then unclip the spring!
unplug electrical connector remove rubber boot unclip spring and swing spring back. pull out old halogen bulb from bracket. replace with new bulb (not toching glass) swing back spring and clip to housing replace rubber boot plug in connector Test headlights...finished
To change the wiper blade on a Peugeot 306 unclip the old part from the mount. Take the new wiper blade and slide it into place until it clicks.
you open the bonnet and then you go to the back of the headlight and youll see a wire and clip attached to the black casing unclip that wire and then unscrew the black plastic screw then youl have a clip unclip it and then pull out your light bulb and then put a new one in and put the clip back on and
Inside the engine compartment, unscrew the plasic cap over the back of the headlight, then unclip the bulb. After you pull out the bulb the plug just pulls from the bulb.
unclip H1 connector, it's really on there I needed a pry tool. pull off dust cover (rubber grommet) there will be a spring clip holding the bulb in. push in, push to the side and release. bulb will come out when spring clip is removed. depending on the bulb that's going back in, it might be better to pull the bumper off.
Open the hood. Remove the top bolts holding the grille to the radiator support. Squeeze the 4 retainer clips together to release them from the radiator support and pull the grille forward towards the front of the vehicle.. Unclip the headlight and parking light wiring from their holders while holding the grille. Reverse the procedure to install or replace the grille.. Done
Open the hood & look for two white sliding clips. Pull them up to remove them. The headlight assembly should easily pull out. Identify the wiring harness & unclip it. Reverse the procedure to reinstall