0
What else can I help you with?
What is the total number of board feet in two pieces of 1 in?
1 board foot is a board that is 1 foot long, 1 foot wide and 1 inch thick, so since you did not give length and with of the boards there is no way to answer your question.
If you do a heel flip and front of your board what do you do to land on the board?
make sure your foot wait are equal if you put your toes out on front foot then you put your heel out on back foot same for putting your front foot in.
How many 6 x 6 blocks can be made out of a 4 foot board?
Assumption: 6 x 6 is using inches as the unit (half a foot) and a 4 foot board means 4 square feet of board. Each square foot of board can be cut into four half foot x half foot pieces. Therefore, the 4 foot board would be able to make 16 half foot x half foot (6 inch x 6 inch) blocks.
Meg has 18 feet of ribbon that she wants to divide into of a foot pieces. How many of a foot pieces are there in 18 feet?
If you have 18 feet of ribbon and you want to cut the ribbon every 12 inches which is a foot. You will have 18 twelve inch pieces. if I am understanding your question correctly. Eighteen feet would equal 18 one foot pieces.
Cutting a 10 foot plank into 10 equal sections if it takes 1 minute per cut how long will it take him to get the 10 equal pieces?
NOTE: The problem asks to cut the board into 10 equal parts, not into equal boards proportional to the original piece of wood. Case 1: CANNOT stack wood on top of each other. Assume the board 5 feet by 2 feet. If you made one horizontal cut in the center of the board 1 foot from each edge, and then made four vertical cuts at 1 foot apart, you would then have 10 equal pieces at 1' by 1' each. Time taken: 5 minutes for 5 cuts. Case 2: CAN stack wood on top of each other. The board is 5 feet by 2 feet. Cut the board long way 1 foot from the middle and the result is 2 boards 5 feet by 1 foot. Stack these two boards on top of each other. Then, cut the stack vertically one foot from the end now making 2 pieces of wood 1' by 1' and 2 pieces of wood 4' by 1'. Then, take the 2 pieces of wood 4' by 1' and stack them on top of each other. Cut vertically once in half, so you now result in 4 boards 2' by 1'. Finally, stack these 4 pieces of wood on top of each other. Cut once vertically and you now have 8 pieces of wood 1' by 1' (plus the 2 from earlier which now make 10). Time taken: 4 minutes for 4 cuts.
What is a 2.9 Board foot?
A board foot is 12 inches by 12 inches, 1 inch thick. Any combination of measurements that equal this is 1 board. 6x24x1 is 1 board foot. 2.9 board foot could be anything. There should be another measurement saying what this is. Board foot is used to figure cost as most common wood is the same price per board foot. Could be 2x4, 2x12 or 1 inch, it all works out the roughly the same price.
How many inches in a board foot?
A board foot is a unit of measure for lumber volume equal to 144 cubic inches, which is equivalent to a board that is 1 inch thick, 12 inches wide, and 12 inches long.
Steve cut a board 8 feet long into three equal pieces how long was as piece?
Oh, dude, let's break it down. If Steve cut an 8-foot board into three equal pieces, each piece would be 8 divided by 3, which is approximately 2.67 feet long. So, like, each piece would be around 2 feet and 8 inches long. Math can be fun, right?
Cassie has a wood board that is 3434 foot long. She wants to cut the board into pieces that are 1818 foot long. Which expression will help Cassie find how many pieces she can cut?
3434/1818.However, a more reasonable expression is "A piece of wood board which is nearly two thirds of a mile long is so unlikely that I must have made a mistake in recording its length and so I had better do it again!"
How can you cut an 8 foot by 3 foot board into two pieces so that both pieces together cover a 12 foot by 2 foot hole?
There is no way to do this with two pieces. You can do it with 4 (making each 3 by 2) The only way is by having three pieces.... note: The total area is the same so it has to be possible (24sf) 2 cuts total (3 pieces): STEPS>>> 1st: Cut the board into two pieces. Making one piece 8'x2 the other piece then is 8'x1'. 2nd: Cut the 8'x1' piece into half making two 4'x1' pieces. 3rd: Place the two 4'x1' pieces together to make it 4'x2'. 4th: Place the 8'x2' & new 4'x2' pieces together for your desired dimension, 12'x2'
What is a sixth of a foot?
Oh, dude, a sixth of a foot is like, you know, one-sixth of a foot. So, if you have a foot, just chop it into six equal pieces, and there you have it! It's like basic math, but with feet.
A sub sold sandwiches that were one-fifth of a foot long. If you were to cut the sandwich into 3 equal pieces. What fraction of a foot would each piece be?
One fifteenth
