answersLogoWhite

0

What you do is you need to get an old toothbrush and get some water and soap...first try to get the gum off WITHOUT the water or soap then if that does not work use the water and soap. make sure when you get the water is is warm to hot water..

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you remove drivers seat-belt?

To remove a driver's seat belt, first locate the buckle and unfasten it. Next, find the anchor point where the seat belt is attached to the car's frame, usually near the floor or the side of the seat. Use a socket wrench or appropriate tool to remove the bolt securing the seat belt. Finally, pull the seat belt out from its retractor to fully remove it.


How do you remove Toyota Tacoma seat belt?

To remove the seat belt from a Toyota Tacoma, first, locate the bolt that secures the seat belt buckle or retractor to the vehicle's floor or pillar. Use a socket wrench to remove the bolt and detach the seat belt. If the seat belt is stuck, ensure that the seat is in the proper position and check for any obstructions. After removing the old seat belt, replace it with a new one by reversing the process.


How do you remove seat belt from Toyota Celica 2000?

To remove the seat belt from a 2000 Toyota Celica, first, locate the bolt securing the seat belt anchor to the car's body. Use a socket wrench to remove this bolt. Next, detach the seat belt from any clips or guides along the seat or pillar. Finally, pull the seat belt free from its routing path in the vehicle.


How do you remove the seat belt in a Ford Fiesta 1999?

To remove the seat belt in a 1999 Ford Fiesta, start by locating the seat belt buckle and the retractor. Use a screwdriver to remove any screws securing the plastic cover around the retractor and the buckle. Once the cover is off, unbolt the seat belt from its anchor points using a socket wrench. Finally, gently pull the seat belt out of the retractor and remove it completely from the vehicle.


How do you replace a rear seat belt?

remove the seat to access screws


How do you remove seat belt in Buick Lacrosse?

To remove a seat belt in a Buick LaCrosse, first, ensure the vehicle is turned off and the seat belt is not in use. Locate the bolt that secures the seat belt buckle or anchor point, usually found on the floor or the side of the seat. Use a socket wrench to remove the bolt, and then gently pull the seat belt free from its anchor. If needed, consult the vehicle’s owner’s manual for specific instructions or safety precautions.


How do you remove automatic seat belt in 1990 mercury topaz?

To remove the automatic seat belt in a 1990 Mercury Topaz, first, disconnect the vehicle's battery to ensure safety. Then, carefully remove the trim panel around the seat belt mechanism, typically held by screws or clips. Locate the seat belt motor and wiring, disconnect them, and then unbolt the seat belt assembly from the vehicle. Finally, reassemble any trim panels you removed.


Cavalier seat belt remove?

To switch out a seat belt usually the seat needs to be removed first. Then it is in most instances just a bolt to be removed.


How do you remove seat belt buckle in a Toyota corolla?

Remove lower seat cushion by popping the front of it upward from the 2 retaining clips, then sliding it forward. The seat belt buckle is bolted to the floor.


How do you remove driver side seat BELT?

To remove the driver side seat belt, first, ensure the vehicle is parked and the engine is off. Locate the seat belt retractor, usually mounted on the side of the seat or the floor. Use a suitable tool, often a socket wrench, to remove the bolts securing the retractor and the buckle to the vehicle. Once the bolts are removed, gently pull the seat belt out to detach it completely.


How do you remove a passenger side front seat belt in a 1999 Toyota corolla?

To remove the passenger side front seat belt in a 1999 Toyota Corolla, first, ensure the vehicle is turned off and the seat is in a forward position. Locate the seat belt anchor bolt at the base of the B-pillar and use a socket wrench to remove it. Next, detach the seat belt from the retractor mechanism by accessing the rear side panel if necessary and unbolting it. Finally, pull the seat belt free from its guides and clips.


How do you remove rear seat belt on corsa c?

To remove the rear seat belt on a Corsa C, first, ensure the vehicle is parked and the ignition is off. Locate the seat belt anchoring point, usually at the base of the seat or on the side pillar, and remove any covers if necessary. Use a socket wrench to unscrew the anchor bolt, then slide the seat belt out of its guide. Finally, check for any additional clips or fasteners that may need to be released before fully removing the belt.