answersLogoWhite

0

Check for a vacuum leak somewhere. It might just be a cracked rubber vacuum line. Try short sprays of starting fluid at or near a suspected vacuum leak. You'll hear the engine idle speed change immediately if you find a leak.

User Avatar

Wiki User

19y ago

What else can I help you with?

Related Questions

What does a 1989 Chevy pickup have for fuel system?

If it hasn't been changed, it has Throttle Body Injection (TBI). It looks similar to a carb but it will have wires running to it.


Fuel pressure for 1998 sonoma?

Throttle Body Injection (TBI) Aprox. 9 - 13 psi with key on, not running and a 3 -10 psi drop when running at idle. Multiport Fuel Injection (MFI) Aprox. 41 -47 psi with key on, not running and a 3 -10 psi drop when running at idle. Central Multiport Fuel Injection (CMFI) Aprox. 58 -64 psi with key on, not running and a 3 -10 psi drop running at idle. Central Sequential Electronic Fuel Injection (CSEFI) Aprox. 55 -61 psi with key on, not running and again the 3 -10 psi drop running at idle.


How do you clean fuel injectors on a 1994 Buick Roadmaster?

Doesn't a 94 Buick have Throttle Body Injection? Try running injector cleaner through the fuel system first. As always, follow the manufacturers recomendations.


What is idling fule pressure for a 1995 s 10 with 4.3 vortec?

With key on engine not running pressure should be 9 to 13 psi Engine at idle pressure should decrease by 3 to 10 psi on a throttle body. On a multi port injection key on engine not running pressure should be 41 to 47 psi. Engine running at idle pressure should decrease 3 to 10 psi. Central multiport fuel injection key on not running should be 58 to 64 psi. Engine running at idle pressure should decrease 3 to 10 psi. Central sequential electronic fuel injection key on not running pressure should be 55 to 61 psi. Engine running at idle pressure should decrease 3 to 10 psi.


Where is the throttle positioning sensor on a 1988 accord?

Throttle position sensor is located on the side of the throttle body-in line with the throttle shaft. To locate the throttle body, you can have someone repeatedly push the accellerator pedal (with the engine not running) while you look for the moving throttle shaft. Drew


Car is running on high idle 2000 Malibu?

There are multiple causes of high idle on this application. They include throttle cable out of adjustment, IAC problems, evaporative emission failure, and vacuum leaks (among others). This is a critical safety issue due to the possibility of uncontrolled throttle and must be diagnosed and serviced by qualified mechanic.


How do you test the throttle position sensor?

Put a used one on from a running one


Why does my lawn mower start running full throttle even at full choke?

no


Change a throttle position sensor for 05 altima?

The throttle position sensor determines the amount of throttle used when the engine is running at various speeds. If the sensor is faulty, it can be replaced by ordering a new part.


Where is the map sensor located on a 1995 Chevy 350 throttle body?

Passenger side of engine next to throttle body. It is the senor with the vacuum line running to it.


What if your Volvo S40 will not stay running unless you keep your foot on the gas pedal?

probably failed throttle bypass solenoid or possibly throttle position sensor


Your 2000 Toyota Celica starts to idle then cuts off completely and wont stay running unless you give it gas Any suggestions?

you may look into what is called a throttle position sensor. it basically monitors the position of the throttle and tells the fuel injection what to do. if it goes bad, the car will stall and won't run unless you give it more gas to keep the rpm's up. the throttle position sensor is typically located on the side of the throttle body, right near where the air intake hose joins the engine. they are relatively inexpensive , available at any car parts store and easy to replace.