0
I replaced the timing belt on my 1992 Honda Accord a few months ago. If you don't have 4-8 hours, a 3/4 inch breaker bar, a cheater bar, and a tool to hold the huge pulley in place don't try it. You will also need two jacks. One of them will be for the motor and the other will be for the wheel well. Your 1988 will be just as difficult, if not more difficult to accomplish.
Raise and support the vehicle on jack stands. Remove the left (driver's side) wheel and inner fender panel. Remove the splash shield. Remove the accessory belts and the top engine mount. Remove the valve cover.
Step 2 Turn the engine counter clockwise until the engine is on top dead center on number 1 cylinder. To do this look on the top of the transmission for the rectangular hole in the bell housing and the pointer pointing toward the block. Turn the engine until you see a T and a line next to it. If the car is an automatic turn the engine and watch the flywheel for these marks. Put the pointer on the line and you have top dead center. If the car is a manual transmission put the pointer on the T.
Step 3 Remove the crankshaft pulley bolt and pulley. Remove the timing belt covers. Check the timing marks one more time and make sure the camshaft sprocket has the word UP in the up position. Loosen the timing belt tensioner and push it away from the belt and loosely tighten it to hold it out of the way. Remove the timing belt.
Step 4 Install the new timing belt starting on the left side from the crank over the camshaft sprocket and down on the inside of the tensioner and over the outside of the oil pump. Loosen the tensioner and let it apply tension to the belt and then tighten the bolt.
Step 5 Make sure all the tension is on the side opposite of the tensioner or the left side. Double check the timing marks to make sure they are still lined up. Turn the engine counter clockwise for about three to four teeth on the camshaft sprocket and then loosen the bolt in the tensioner and let it take up the remainder of the slack in the belt. Tighten the tensioner bolt to 31 foot pounds of torque.
Step 6 Install all components in reverse order of their removal. Tighten the crankshaft bolt to 108 foot pounds of torque.
What else can I help you with?
Does a 1988 Honda Accord have timing marks for when you change the timing belt?
Yes, a 1988 Honda Accord has timing marks that are used to properly align the engine's timing when changing the timing belt. These marks are typically located on the crankshaft and camshaft gears, allowing for correct installation of the new belt. It's important to align these marks accurately to ensure the engine runs smoothly after the replacement. Always consult the vehicle's service manual for specific details and procedures.
What is the 1988 Honda accord timing belt longevity?
5 years or 60,000 miles, whichever comes first.
Where is the timing belt on a 1988 Honda accord dx manual?
looking @ left side of motor right @ valve cover.
How do you set the timing chain on a 1988 Honda xr200r?
how do you adjust the timing on a 1988 honda xr200
What brand engine will fit in your 1988 Honda accord?
Honda.
Is a 1988 Honda Accord fast?
Absolutley not.
How do you check the transmission fluid in a 1988 Honda Accord dx found the plug but how do you read it?
how do i check the transmission fluid on a 1988 Honda accord, it is a automated
Can you use a transmission from a 1990 or 1993 Honda Accord for your 1988 Honda Accord?
no u cannot do that bolt pattern is different
What is the battery size for a 1988 Honda Accord LX?
The battery size for a 1988 Honda Accord LX is a size 25. The battery can be purchased at any auto parts store.
Is the 1988 Honda Accord lxi an interference motor?
The 1988 Honda Accord LXi is equipped with a 2.0-liter engine that features an interference design. This means that in the event of a timing belt failure, the pistons could collide with the valves, potentially causing significant engine damage. Therefore, it's crucial to maintain the timing belt and replace it according to the manufacturer's recommended schedule to avoid such issues.
What is the bolt pattern on a 1988 Honda accord lxi?
4x100
What ford parts will fit on a 1988 Honda accord?
None
