0
This procedure s fairly generic so it should suit most makes of vehicle, but you should always consult your vehicle manual for acurate servicng and to help you locate parts specific to your vehicle.
* First remove the Radiator cap. * Un-do the bottom radiator hose clamp with a screw driver or spanner.
(either at the engine block side or radiator side which ever is easier to access)
* Next remove the hose from the outlet by manipulating it with your hands (boiling water poured on the outside of the hose can help here) * Let all the fluid run out of the radiator and engine block (into a recepticle for diluted disposal in garden)
Job done.
If you were to refill the radiator...
* Flush the radiator out with a hose from top to bottom until the water exiting runs clear
To be thourough you should also remove the thermostat and flush the engine block from the top (and replace the thermostat with a new one).
* Refit the hoses and tighten hose clamps.
* Slowly refill the cooling system with a decanter of water and engine coolant
* Check all hose clamps are tight and start engine - leaving the radiator cap off.
* run engine till it reaches standard opperating temperature or beyond and all air has escaped the sytstem this part is very important.
* once it has returned to standard operating temperature replace radiator cap.
* carry water in your car and watch the temperature guage while driving.
* In the days following the flush recheck the hoses and level of radiator to ensure the fluid doen't leak out. Good luck...
What else can I help you with?
Where can you find the radiator drain plugs on a Mazda 323 Interplay?
the radiator drain plug is located on the bottom of the radiator,on the radiator
Where is theThermostat for 1995 Mazda 929?
The thermostat for a 1995 Mazda 929 is located in the engine compartment, specifically at the engine's water outlet housing. To access it, you typically need to remove the upper radiator hose, as the thermostat is situated underneath this hose. Make sure to drain the coolant before attempting to replace it to avoid spills.
Drain coolant Mazda 626?
To drain the coolant on a Mazda 626, locate the drain plug on the bottom of the radiator. Remove the plug and drain the coolant into a pan.
Where is a coolant drain plug in a 95 Mazda protege?
bottom of the radiator
Where is the thermostat on 1992 Mazda 929?
The thermostat, on your 1992 Mazda, can be found on the front bottom portion of the engine. You can follow the water hose from the bottom of the radiator to the thermostat.
How do you replace the radiator in a Mazda Protege 2000?
Drain the water from your Mazda Protege radiator. Remove the hoses from your radiator. Remove the radiator stabilizing arm. Remove the radiator retaining bolts. Reverse the process to install the new radiator.
How do you drain coolant on 2002 Mazda Protege 5?
there is a tap at the bottom of the radiator
Where is the coolant drain plug on a Mazda Tribute?
Drain plug for the radiator for Mazda Tribute 2001 is located on the right side bottom of the radiator. You'll need to remove the right side mud guard to be able to access it.
Where is the radiator drain located on a Mazda?
There is no drain. Loosen the clamp on the lower radiator hose at the drivers side and allow it to drain. The hose can be located from underneath the car once the plastic splash shield is removed.
What is a timing cover seal and where is it at on a Mazda 929?
What is a timing cover seal on a 1992 mazda 929 and where is it located at?
Power brake 1990 Mazda 929 fails?
929 1990 Mazda power brakes fails
Where is the thermostat located on a 1989 Mazda 929?
The Thermostat is located at the low side radiator hole housing ( one end of the hole is connect from the radiator and the other end is connect to the housing
