answersLogoWhite

0

The two red wires on Halo projectors are the power source for the product. Splice the two red wires into the appropriate wire source on the engine bay.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

How to wire in halo headlights?

You can wire in halo headlights by following instruction in its manual.


How do you install halo projector headlights on a 2000 ford expedition?

If you already got the halo assembly if not you need to go and get new halo headlights eBay i got mine for celica free shipping, then when you get them just connect up all the wires and then there will be one extra wire that you will have to ground to make halos work. All done nice cool looking headlights good job :)


How do you install new halo headlights in your 1998 528i There is an extra wire harness with the new lights?

How to install headlights to a BMW 528i?


How do you install halo eyes on a eclipse 1995 I took the lights to a shop and they connected my halo together with the headlight any suggestions on how come they connected that way?

I'm guessing the shop that you went to just didn't think about the effect you wanted to acheive. The wire to the halo light has to be powered from somewhere, and they just took the easiest route and chose the headlight wire. But you could use another source. I recommend connecting the halo to your parking lights, that way they will come on before the headlights. If you connect them via a separate switch, it is more work, more wires to run, and you run the risk of leaving them on accidentally (eventually draining your battery). If you hook them up through the parking lights, they will turn off when you turn your parking lights go off, while still coming before your headlights do. You will have to take one wire (the halo +12 wire), disconnect it from the headlights and connect it to the parking lights instead. You do not need to change the (halo GND) connection, since it is already grounded. Hope this helps...


How do you install halo projector headlights on a 2005 srt 4?

Halo projector headlights are direct bolt-ons to a 2005 SRT 4. To install a unit mount the light to the bracket in the front bumper. Connect the light plug to the wire harness and splice in the side markers.


Do you know how to set up wiring to install halo headlights for a 2000 maxima?

I tapped into the parking light wire harness both (+) and (-) and it works and looks great!


How do you Add hallo headlights to a grand prix?

Open the hood and there are two bolts attached to the headlights. remove them, and slip the old headlights out. By the way, you need to purchase preassembled halo's, you cant put halos on a stock setup. Anyway, slide the old headlight towards the outside of engine bay (towards the fenders on the nearest side) and then you can take out the light harness from those and put them in the new setup. they are ready for the wire harness, you will need to solder or splice the positive (red) and negative (black) wires that are hanging freely, to the corresponding positive and negative wires in the headlights (make sure that they are the wires that will have power when the lights are on, not the brights, i did that on accident and had to redo it) then clip the wire harnesses together and slide them into the holders. reattach the bolts and youre done. If you have questions still email me at steinbacher682@hotmail.com ill clarify and I'll include pictures.


What color wire is the power wire on your headlights on your 1995 Chevy pickup?

just use a light tester, clamp the gator clamp on a ground turn your light on and jam the tip into differant wires on the plug, you will actually have 2 power wires, one for low beams and 1 for high beams


What are the 3 wires going into the headlight on a Nissan Sentra?

Nearly all vehicle headlights (with a single lamp on each side) have three wires: Vehicle Ground (usually black) and one wire for the Low beam and one for the High beam.


What causes headlights to dim and smoke come from the vent?

it is probably a short circuit if it is dimming your lights. the smoke is burning insulation on the wires. it must be an wire that is not protected by a fuse. do you have an aftermarket stereo?


2001 Pontiac sunfire daytime running lights not working and hi beam headlights turn off all headlights?

Had the same problem. Found it to be a bad ground wire for the headlights. There are two ground wires for the headlights, both are directly below the battery. You can see one of them if you remove the drivers side headlight. It is right behind the radiator hose. The other is a few inches from that one.


How do you connect daytime running lights for 2004 Honda Element?

First you must be able to use a test light. .. Remove the clam shell that encloses the steering column. Then with the key off and removed find the bundle of wires that go to the light switch. Turn on the head lights and probe the wires one by one till you find one that lights up. STAY AWAY FROM THE YELLOW WIRE BUNDLE THIS IS THE AIR BAG YOU WILL DIE. With the light probe lit turn off the headlights and if the probe goes out you have found the running light wire , try again till the wire goes out as the headlights do. First you must be able to use a test light. .. Remove the clam shell that encloses the steering column. Then with the key off and removed find the bundle of wires that go to the light switch. Turn on the head lights and probe the wires one by one till you find one that lights up. STAY AWAY FROM THE YELLOW WIRE BUNDLE THIS IS THE AIR BAG YOU WILL DIE. With the light probe lit turn off the headlights and if the probe goes out you have found the running light wire , try again till the wire goes out as the headlights do.