0
What else can I help you with?
What Size is the axle nut on a Mazda Protege 5?
fronts are 32mm
How do you remove a CV axle from the transmission on a 1995 Mazda Protege and replace it?
To remove the CV axle from the transmission on a 1995 Mazda Protege, first, lift the vehicle and secure it on jack stands. Remove the wheel and brake components to access the axle. Disconnect the axle nut and any retaining clips, then gently tap the axle out of the transmission using a hammer or pry bar if necessary. To replace it, simply reverse the process: insert the new axle into the transmission, secure it with the retaining clips, and reassemble the wheel and brake components.
How do I perform a bicycle front axle replacement?
To perform a bicycle front axle replacement, you will need to remove the wheel from the fork, unscrew the axle nuts, slide out the old axle, insert the new axle, and tighten the axle nuts securely. Make sure to adjust the bearings and reassemble the wheel onto the fork before testing the bike for proper function.
How do you replace a CV Axle in a 1.5L 95 Mazda Protege without Anti Lock Brakes?
Not easy!!! Get a manual on your car and it will help on the next repair.
How do I perform a bike wheel axle replacement?
To perform a bike wheel axle replacement, you will need to remove the wheel from the bike frame, release the quick release or axle nuts, slide out the old axle, replace it with a new one of the same size, and then reassemble the wheel onto the bike frame. Make sure to properly adjust the bearings and secure the axle in place before riding.
How do I perform a bike rear axle replacement?
To perform a bike rear axle replacement, you will need to remove the wheel from the bike frame, unscrew the axle nuts or quick release skewer, slide out the old axle, replace it with a new one of the same size, and then reassemble the wheel onto the bike frame. Make sure to properly adjust the axle alignment and tighten the nuts or skewer securely.
How to fill manual transmission on Mazda Protege?
very long thin funnel from the top under air box into top fill hole on trans axle very slowly
How do I perform a mountain bike axle replacement?
To perform a mountain bike axle replacement, you will need to first remove the wheel from the bike. Then, use the appropriate tools to unscrew the axle nuts or quick release skewer. Once the axle is removed, you can replace it with a new one by inserting it through the hub and securing it with the nuts or skewer. Make sure to tighten everything properly and test the wheel before riding.
How do you need to change cv joint on a Mazda protege?
To change the CV joint on a Mazda Protegé, first lift the vehicle and securely support it on jack stands. Remove the wheel and the axle nut, then detach the lower control arm and any other components obstructing the axle. Pull the axle out of the hub and replace the CV joint, ensuring proper greasing and sealing. Reassemble the components in reverse order, making sure everything is tightened to the manufacturer's specifications.
How do I perform a bike wheel hub replacement?
To perform a bike wheel hub replacement, you will need to first remove the wheel from the bike. Then, use a wrench to loosen and remove the axle nuts or quick release skewer. Next, slide the axle out of the hub and remove the old hub from the wheel. Install the new hub into the wheel, making sure it is properly aligned. Finally, insert the axle back into the hub, tighten the axle nuts or quick release skewer, and reattach the wheel to the bike.
How do You replace drive axel's on 1998 Mazda Protege?
tire off, brakes off, tie rod off, disconnect strut, and a few holding bolts. axle will slide out with a little bang from a hammer or a little pull if your lucky
How do I perform a bike rear wheel hub replacement?
To perform a bike rear wheel hub replacement, you will need to first remove the wheel from the bike frame. Then, using the appropriate tools, disassemble the hub by removing the axle and bearings. Install the new hub by inserting the axle and bearings, and then reassemble the hub. Finally, reattach the wheel to the bike frame and ensure it is properly aligned and tightened.
