0
To replace fog lamps in a 2004 Subaru Forester, you will need:
Eye protection
H3 lamp(s)
10mm socket
12mm socket
6" extention
tools to remove the plastic stone guard (trim pad puller or suitable substitute)
thin-bladed screwdriver (to separate the connecter between the lamp assembly and the main wiring harness)
Ramps are nice but may not be necessary if you're skinnier than I am Stout wheel chocks for the rear wheels if using ramps in the interest of safety. Drop light is also really nice.
1. Remove the plastic splash tray by removing 4 12mm bolts. Two toward the front, two in the back on the transmission mount Also, there are 2 plastic clips on the tray that help hold the thing in position while installing or removing the tray.
2. Remove about six plastic expandable buttons that hold the stone guard in place
3. Remove two more of these buttons on each side that hold plastic trim below the fog lamp assemblies and bend out of the way.
4. Each lamp assembly is held in place by two bolts with 10mm heads. On mine, the upper bolt has a combination 10mm/Phillips head.
5. From underneath the bumper, disconnect the two-wire connecter, and remove the two bolts mentioned in step 4.
6. Twist/pull/slide the lamp assembly forward through the bumper and set aside.
Now we're into the meat of the problem. I found it was best to perform the following on a table in a warm environment with good lighting.
7. You will see a black plastic ring with the word "top" embossed on it. Two wires will bo through that to the lamp assembly. Turn the ring counter clockwise to release the ring. On the side facing the bulb you will find a connector that goes to the bulb. Pry that connector gently from the ring. Remove the wire from the connector.
8. Locate the spring retainer that holds the lamp into the assembly and release the catch.
9. Remove the defective bulb from the assembly and install the new bulb being careful not to get skin oil on the new bulb. I wore a pair of latex gloves when installing the bulb.
Assemble in reverse order.
What else can I help you with?
How do you change brake light bulb on 2003 Subaru Forester?
Not to be unkind - but READ THE MANUAL.
Fog light change bulb?
How do you change a fog light bulb on a 2004 VW Passat?
Why is the fog light not working on 2002 Subaru Forester?
Replace the bulb, had to change one myselfe.
How do you change a license plate light bulb on a 2004 Buick Regal?
=== ===
Change brake light on a Nissan Altima?
how to change the rear tail light bulb on a 2004 Nissan maxima
How do you change the brake light on a 2006 Subaru Forester?
To change the brake light on a 2006 Subaru Forester, first, open the rear hatch and locate the tail light assembly. Remove the two screws securing the tail light, then gently pull the assembly out. Twist the bulb socket counterclockwise to remove it, replace the old bulb with a new one, and reassemble by reversing the steps. Make sure to test the new bulb before securing everything back in place.
How do you change the map light on a 2004 Grand Caravan SXT?
The map light on a 2004 Dodge Grand Caravan SXT is changed gently prying the edge of the cover to reveal the bulb. The bulb can then be popped out and a new bulb installed.
How do you change a parking light on a Subaru Forester?
This was answered last week and is a simple procedure. One Phillips screw holds the parking light on in my 2000 Forester. You open the hood, remove the screw, pull the lamp assembly out and you have access to change the bulb. If you are asking about changing the whole assembly, the answer is the same. --Ken
How do you change the tail light bulb on a 2004 ford focus?
Sedan or hatch makes a difference
How do you change the dome light bulb in a 2002 Lexus RX 300?
how do i change front interior light for lexus rx 300 2004 model
How do you change a plate bulb on a 2004 escalade?
To change the plate bulb on a 2004 Cadillac Escalade, first, open the rear liftgate and locate the light assembly above the license plate. Remove the screws or clips holding the light assembly in place, then gently pull it out. Disconnect the old bulb by twisting it counterclockwise, replace it with a new bulb, and reassemble the light assembly by reversing the steps. Finally, test the new bulb to ensure it works.
How do you change the license plate light bulb on a 2004 Acura RSX?
To change the license plate light bulb on a 2004 Acura RSX, first, open the trunk and locate the license plate light assembly. Use a small flathead screwdriver to gently pry off the light cover. Remove the old bulb by twisting it counterclockwise, then insert the new bulb in the same way. Finally, snap the cover back on and close the trunk.
