0
How do you disconnect the canister to remove the fuel pump on a 2000 Mitsubishi Galant?
I am a female and yesterday i just changed my fuel pupm and filter which is located underneath the backseat inside the gas tank. You may need an assistant to help you because some of the hoses got in my way.
First of course you have to remove the back seat. There is a black lever under the right and left side of the bottom of the seat. Once you remove the seat there is a silver, square lid that is held down by four (4) phillip head screws. remove this carefully because there are wires and plugs inside that you do not want to rip off.
once you unscrew that piece, unplug the blue and black sockets. There are two hoses that need to be disconnected. the hard, black plastic piece must be removed by using a hammer and flathead. Carefully bang it counterclockwise to remove. Once that that piece is off, pull up the canister (it is a white canister) BE CAREFUL!! THIS IS FULL OF GAS AND NEEDS TO DRAIN!! Once it drains the canister must be taken apart to reveal the pump . There are alot of steps to do that but if you look at it you can figure out how to disassemble the canister.
I hope that this was helpful.
What else can I help you with?
How do you disconnect electric Ariel on Mitsubishi Galant?
If you are referring to an electric antenna, there should be a snap-connector to the motor assembly-just remove it.
How do you remove Mitsubishi Galant Axle?
Unbolt it.
How Do you change the Evaporator On a 2002 Ford Explorer?
# Disconnect negative battery cable # Raise truck and secure it # Remove the fuel tank # Disconnect the vapor hoses from the canister and remove the canister retaining nut then remove the canister
How do you remove the alternator of a 2000 galant with a 4-cylinder?
To remove the alternator from a 2000 Mitsubishi Galant with a 4-cylinder engine, first disconnect the negative battery terminal to ensure safety. Then, remove the serpentine belt by loosening the tensioner. Next, unbolt the alternator from its mounting bracket and disconnect the electrical connectors. Finally, carefully lift the alternator out of its position for replacement or repair.
How do you replace alternator on Mitsubishi Galant 2000?
To replace the alternator on a 2000 Mitsubishi Galant, first disconnect the negative battery cable and remove the drive belt by loosening the tensioner. Unbolt the alternator from its mounting bracket and disconnect the electrical connectors. Install the new alternator by reversing the removal steps, ensuring all connections are secure, then reattach the drive belt and reconnect the battery. Finally, start the engine to confirm the new alternator is functioning properly.
How do you remove the spare tire from trunk on a 2000 Mitsubishi galant es?
you dont its just for show evidently
How do you remove yellow plastic fuse holder in a 2003 Mitsubishi galant?
you just pull it like a fuse
How do you remove the Evap canister on the Nissan Sentra?
To remove the EVAP canister on a Nissan Sentra, first ensure the vehicle is parked on a level surface and the engine is off. Disconnect the negative battery terminal, then locate the canister, typically found near the fuel tank or under the vehicle. Remove any mounting bolts and disconnect the hoses and electrical connectors attached to the canister. Finally, carefully take out the canister and replace it with a new one if needed.
How do you replace expansion valve on 2002 Mitsubishi Galant?
To replace the expansion valve on a 2002 Mitsubishi Galant, first, ensure the AC system is fully discharged to avoid refrigerant release. Remove the dashboard panel and the evaporator case cover to access the valve. Disconnect the refrigerant lines and the electrical connector from the old expansion valve, then remove it from the evaporator. Install the new valve, reconnect the lines, and reassemble the dashboard before recharging the AC system.
How do you replace the instrument panel lights in 2002 Mitsubishi Galant?
To replace the instrument panel lights in a 2002 Mitsubishi Galant, first, disconnect the negative battery terminal for safety. Remove the screws securing the instrument panel bezel and carefully pull it away to access the gauge cluster. Unscrew the cluster from the dashboard, then twist the bulb sockets counterclockwise to remove them and replace the old bulbs with new ones. Reassemble the cluster, bezel, and reconnect the battery.
How do you change blinker switch on 2000 galant?
To change the blinker switch on a 2000 Mitsubishi Galant, first disconnect the negative battery terminal to ensure safety. Remove the steering column cover by unscrewing the screws and gently prying it apart. Once exposed, locate the blinker switch, disconnect its wiring harness, and remove the screws securing it in place. Install the new switch by reversing the process, ensuring everything is securely fastened before reconnecting the battery.
How do you remove and install the water pump on a 1990 Mitsubishi Galant 2.0L?
use the remove timing belt instructions and it includes the water pump,"if your in there do them all !"
