0
What else can I help you with?
How much is it to replace a 99 Mazda protege serpentine belt?
The cost to replace a 1999 Mazda Protege serpentine belt will vary depending on the cost of parts and cost of labor. The prices for the serpentine belt start at $14.56.
How do you release tension on the power steering belt in order to change it on a 1994 Mazda Protege?
i need to change my alternator belt and don't know where the tension wheel is so i can take off the other belt to replace the alternator belt on my 94 Mazda protege 1.6l
How do you take off alternator tension on a 99 Mazda 626 v6 car?
To release the alternator tension on a 1999 Mazda 626 V6, first, locate the tensioner pulley, which is typically near the alternator. Use a wrench or ratchet to rotate the tensioner pulley counterclockwise, which will loosen the serpentine belt. Once the tension is released, you can slide the belt off the alternator's pulley. Afterward, you can remove the alternator if needed.
How do you get 2001 Mazda protege serpentine belt off?
To remove the serpentine belt from a 2001 Mazda Protege, first, locate the tensioner pulley. Use a wrench or a ratchet with the appropriate socket to rotate the tensioner counterclockwise, which will relieve the tension on the belt. While holding the tensioner in this position, slide the belt off the pulleys. Finally, carefully release the tensioner and remove the belt completely.
What is the routing for a serpentine belt on a 2003 Mazda 6 3.0 v6 dohc?
Serpentine belt diagran 2003 mazda 6
On a 1996 Mazda b2300 2.3 Ltr do I need to take off fan and radiator shroud to get to tension pulley you are trying to replace serpentine belt you are not able to get leverage to get 38 rachet to wrk?
Attach a deep socket and extension bar to the handle of the rachet for more leverage?
How do you put on serpentine belt on Mazda v6 meida?
To install a serpentine belt on a Mazda V6, first, ensure the engine is off and cool. Locate the belt routing diagram, usually found on a sticker near the engine bay or in the owner’s manual. Release tension from the belt by using a wrench to turn the tensioner pulley clockwise, then slide the old belt off and the new belt on, following the routing path. Finally, release the tensioner, ensuring the belt is secure on all pulleys.
How do you tighten belts on 1999 Mazda 626 2.0 engine?
To tighten the serpentine belt on a 1999 Mazda 626 with a 2.0-liter engine, locate the tensioner pulley. Use a wrench or socket to rotate the tensioner counterclockwise, which will relieve tension on the belt. Once the belt is properly positioned, release the tensioner to apply tension to the belt. Make sure the belt is aligned correctly on all pulleys before starting the engine.
How do you replace the water pump serpentine belt on a 1995 Mazda Protege?
powersteering belt off first, then water pump, each has its own ten.
How do you replace the belts on a 1992 Mazda 626?
I am assuming you are meaning the serpentine belt? draw ALL THE PULLEYS on a piece of paper and the bely route, (i draw it on the engine somewhere with a permanet marker) look for the tensioner pully and use the correct means (wrench or ratchet) to push it toward your dash to release the tension and proceed to remove the belt. re route the new correct size belt per your correct diagram and release the tension again to fit the belt into place and let the belt tension... then give her the onion you shouls be good. if you are asking timing belt good luck.
How do you replace the serpentine belt for a 1993 Mazda Protege?
you have to loosen a bolt on the front of the AC compressor, I think its a 12mm. You loosen it and the the AC compressor will then be able to rotate downward, sometimes the compressor gets stuck with age and you might need to tap it down with a mallet. Once the compressor rotates downward the tension in the belt will be gone and you can change the belt. Then tighten the same bolt until you achieve the desired tension
How do you replace the alternator on a 1995 Mazda Miata?
To replace the alternator on a 1995 Mazda Miata, first disconnect the negative battery cable to ensure safety. Remove the serpentine belt by loosening the tensioner, then unbolt the alternator from the engine. Disconnect the electrical connections from the alternator, install the new alternator, reconnect the electrical connections, and reattach the serpentine belt. Finally, reconnect the battery cable and start the engine to test the new alternator.
