0
fist and foremost, make sure you have ample daylight to do this, i learned the hard way. first you take out the speedo cable from the transmission, and feed it through the firewall, not all the way though. then you unscrew the pannels from under the steering wheel, glove box, and take out the shifter cover. there are two screws outside of the guage cluster that you have to remove. take off the a/c and a/c temp. control and there should be 3 screws, take those out. there is a screw hidden behind a tiny panel on the bottom most right part of the black dash panel, take that screw out as well. now you should be able to remove the whole black dash panel as one whole peice. unclip all of the switches from the back of the panel and remove it from your work area. there are 4 screws holding on the guage cluster that also needs to be removed. be careful pulling out the guage cluster because there are two clips or three clips depending on model that need to be removed as well. also, be careful not to pull the speedo cable off the connector, i also learned that the hard way. now you should be able to replace the cluster and just back track these steps to put it all back together
What else can I help you with?
How to install a boost gauge in a Acura Integra?
How to install a boost gauge in a acura integra?"
How do you remove the gauge cluster on a 2003 Acura RSX?
To remove the gauge cluster on a 2003 Acura RSX, first, disconnect the negative battery terminal to ensure safety. Next, pry off the plastic trim surrounding the cluster, then remove the screws securing the gauge cluster in place. Carefully pull the cluster out, disconnect the wiring harnesses at the back, and you can then fully remove the cluster. Reinstalling is simply the reverse process.
Your speedometer on your Acura Integra stop working is their a fuse?
Answermy 99 acura integra has a fuse for gauge cluster, alternator, speed sensor vss o2 sensor is fuse 15 under the dashboard that fuse control all of them check that out
Why is the gauge and running lights not working on 1992 acura integra?
Dimmer switch
How to remove gauge cluster on a 1992 acura integra. I have removed center console and driver and pass. panels to get to additional screws. but won't pop off around ac panel. are there more screws?
why does my speedometer needle bounce, when I'm doin less than 80
How do you replace a speedometer cable on a 1990 acura integra?
Start by removing the gauge cluster, unhook the speedometer cable from back of cluster. Pull speedo cable thru the firewall, follow it down to the transmission, and then unhook it. Install in reverse order of removal.
How do you change the bulbs for the instrument panellights for an Acura Integra?
Changing the instrument panel lights require removal of the dashboard. With the dashboard removed pull the gauge cluster out and take off the bulbs. Install the new bulbs.
Dodge Caravan How do you remove the instrument cluster?
Remove the instrument cluster cover. Each instrument gauge is secured separately with retaining screws. Remove the retaining screws from each gauge. Remove the wiring harnesses from each gauge.
Where is fuse gauge light 98 integra?
In a 1998 Acura Integra, the fuse for the gauge lights is typically located in the fuse box under the dashboard on the driver's side. You'll need to remove the cover to access the fuses, and you can refer to the diagram on the inside of the cover to identify the specific fuse for the instrument panel lights. If the gauge lights are not working, check that fuse and replace it if necessary.
How do you remove 2003 Dodge ram gauge cluster?
To remove the gauge cluster from a 2003 Dodge Ram, start by disconnecting the negative battery cable to ensure safety. Then, remove the trim bezel around the cluster by gently prying it off with a flat tool. Next, unscrew the screws securing the gauge cluster to the dashboard. Finally, carefully pull the cluster out, disconnect the wiring harnesses from the back, and remove it completely.
How do you remove a speedometer on a 1949 F-1 pickup?
The gauge cluster is mounted from behind the dash with three bolts. You have to reach in behind there and remove the three nuts with a small wrench. Once you remove the nuts, the gauge cluster itself will push back through the dash. From there, you can remove the speedo itself from the cluster. The speedometer only has 3 small screws keeping it mounted to the gauge cluster.
Replace bulb in gauge cluster 1995 Toyota Previa?
To replace the bulb in the gauge cluster of a 1995 Toyota Previa, first disconnect the negative battery terminal for safety. Remove the dashboard trim and unscrew the gauge cluster from its mounting. Carefully pull the gauge cluster out and locate the burnt-out bulb; twist it counterclockwise to remove it and replace it with a new bulb. Reassemble the gauge cluster, secure it back in place, and reconnect the battery.
