0
On a 2000 Quest it is buried in the V between the front and rear cylinder banks.
I would make sure it is the real problem before replacing. the sensor alone is $175 and the gaskets are $50. I was quoted 5 hours labor, so apply an appropriate labor charge and it is not inexpensive.
In my case, a misfire only when the engine was hot resulted in an error code for the knock sensor. I replaced the sensor and still have the same problem.
I erased the error code for the knock sensor and it has not come back, but a new error code implied the crank position sensor ($30) was bad. I replaced that sensor but the misfire when hot is still there.
now there are no error codes so I have no clues as to the real problem.
If you go to a dealer, I would insist on ;
a. getting a print out of any and all error codes currently stored in the ECM
b. allowing only the work which you have personally approved
c. getting a written guarantee that the work will fix the problem
too many dealers do not do a good job of analyzing the real problem, fix something unrelated and then say, well, it needed replacing anyway.
What else can I help you with?
Where is the knock sensor located in Nissan quest 2000 and how to replace it?
I AM GETTING A OBD CODE ERROR FOR MY 2000 NISSAN QUEST , PO141 AND PO325 ??? HOW DO I FIX IT..
How do you replace the knock sensor on a 1999 Nissan Quest?
To replace the knock sensor on a 1999 Nissan Quest, first, disconnect the battery to ensure safety. Then, locate the knock sensor, which is typically situated on the engine block. Remove the electrical connector and unbolt the sensor using the appropriate socket or wrench. Install the new sensor, reconnect the electrical connector, and reattach the battery before starting the engine to check for proper operation.
How do you replace knock sensor of 1998 Nissan Quest?
To replace the knock sensor on a 1998 Nissan Quest, start by disconnecting the negative battery terminal to ensure safety. Remove the intake manifold to access the knock sensor, which is located on the engine block. Disconnect the wiring harness from the old sensor, unscrew it, and then install the new sensor by reversing the process. Finally, reconnect the battery and check for any error codes before starting the engine.
What gaskets are needed to replace the knock sensor on a Nissan Frontier?
how many gaskets and which ones are needed when you replace the knock sensor on a Nissan frontier w/a 3.3l v6 engine?
Where is the knock sensor in a 97 Nissan Pathfinder and how can you replace it?
The knock sensor for most Nissan V6 engines is located directly under the intake manifold. So to replace it, you have to remove the intake manifold. Good Luck.
How do you replace the knock sensor in a 1999 Nissan Quest?
With mucho effort, that's how. The sensor is behind the intake manifold, throttle body ect, all of which must be removed. Labor alone will be 5-6 hundred , knock sensor another 150 or so. Good luck.
What is the cost to replace a knock sensor on a Nissan Altima?
If just the knock sensor need to be replaced. I would say no more than $150.00
What causes code p0325 on Nissan Quest?
Code P0325 in a Nissan Quest indicates a problem with the knock sensor circuit, specifically related to the knock sensor's performance or voltage. This can be caused by a faulty knock sensor, damaged wiring or connectors in the circuit, or issues with the engine control unit (ECU). The knock sensor is responsible for detecting engine knock or pre-ignition, and if it fails, it can affect engine performance and efficiency. Diagnosing the issue often requires checking the sensor, wiring, and connectors for faults.
Where is the knock sensor on 98 Nissan Quest?
The knock sensor on a 1998 Nissan Quest is also located under intake manifold and yes alot of work but can be done in a day. 120 dollar part and 500 labor at garage but for u at home mechanics just a simple side project.
How Can you bypass the knock sensor on 1999 Nissan Quest?
Bypassing the knock sensor on a 1999 Nissan Quest is not recommended, as it can lead to engine damage and affect performance. If you're experiencing issues with the knock sensor, it's better to troubleshoot and fix the underlying problem rather than bypassing it. This may involve replacing the sensor or checking the wiring and connections. Always consult a professional mechanic for the best course of action.
Is there the same degree of difficulty in replacing a knock sensor on a 96 Nissan maxima as in the 96 quest?
Never mind, I got my answer.
Where is the knock sensor on a 99 Nissan Quest?
It is behind the intake manifold on the left side of the engine. It will take almost 6 hours to replace this cheesy part ($120) and cost about $500 in labor alone.
