0
* Remove the wheel cover or hub cap.Remove the cotter pin * Break the hub nut loose with a socket and large breaker bar NOTE: If the socket will not fit through the opening in the center of the wheel install the spare * Loosen the lug nuts raise and support car securely on jackstands.Remove the wheel and drain the transaxle lubricant. * Detach the stabilizer bar link(s) from the control arm(s) * Separate the lower control arm from the steering knuckle.Now remove the driveaxle/hub nut * Swing the knuckle/hub assembly out (away from the car) until the end of the driveaxle is free of the hub.If the driveaxle splines stick in the hub tap on the end of the driveaxle with aplastic hammer.Carefully pry the inner CV joint from the transaxle using a large screwdriver or prybar positioned between the CV joint housing and the transaxle housing.Support the outer end of the driveaxle with a piece of wire to avoid unnecessary strain on the inner CV joint * Support the CV joints and carefully remove the driveaxle from the vehicle
What else can I help you with?
How do you replace bad CV joints on a 97 Dodge 1500 4X4?
Sounds like a bad CV joint. On most cars, it is often more economical to replace the complete axle shaft on that side that has a bad cv joint. Hope this helps. Good-luck!
How to remove cv axle on 97 Isuzu rodeo?
hoew do you remove a c v axle from a 97 isuzu rodeo front right
Replace cv joint on Lincoln LS?
don't replace the joint. replace the axle
CV boot Ford Ranger how to replace?
A CV boot is found on the axle of a vehicle. To replace the outer boot remove the axle bolt and pull the boot off. The inner boot requires removal of the whole axle.
How do you replace right cv axle 2002 ford escape?
how to remove, or replace front right axle escape 2004
How do you replace a cv joint in a Honda Odyssey?
Much better to replace the whole axle, look at www.happywrenching.com for a guide on how to replace an axle in a Honda Odyssey
How do you replace CV joint 97 honda accord?
To replace the CV joint on a 1997 Honda Accord, start by safely lifting the vehicle and removing the front wheel. Next, detach the axle nut and remove the lower ball joint to free the axle from the hub. Slide the axle out of the transmission and replace the old CV joint with a new one, ensuring proper alignment and securing it with new clamps. Finally, reassemble the components in reverse order, making sure to torque all bolts to the manufacturer’s specifications.
Does a 1991 toyota corolla have cv joints or do you have to change the whole axle?
It does have CV joints but, it is best to just swap out the complete axle assembly than to replace only the CV joint. You will spend much time and almost as much money trying to replace the CV joint than to just purchase a reconditioned axle assembly and swap it.
How do you replace 2000 dodge ram 1500 front axle cv joint and boots?
The 2000 Ram had u joints, not cv joints at the front axle.
You are ready to replace an axle in your 1993 Nissan Sentra and the axle is stuck in there It will not come out What can you do to get the axle out?
they make a fork to put in between the transmission and the cv axle that attaches to a slide hammer, supporting the cv axle and using the slide hammer the axle should pop out (note I have seen the fork damage the housing of the cv axle if it is a very stumbern fit).
How do you replace CV joint for 1996 Mercury Cougar?
To replace the CV joint on a 1996 Mercury Cougar, first, safely lift and secure the vehicle. Remove the wheel and brake assembly, then disconnect the axle nut and any components obstructing access to the CV joint. Slide the axle out of the transmission and remove the old CV joint from the axle. Install the new CV joint, reassemble the axle into the transmission, and reverse the disassembly steps to complete the installation.
How do you replace front drive axle on a 2002 e320 meredes?
how to install cv axle on a 2002 e32o meredes
