answersLogoWhite

0

* To remove the outside door handle and lock assembly raise the window and remove the door trim panel and watershield * Working through the access hole disengage the plastic clips that secure the outside handle to latch actuating rod and the outside door lock to latch actuating rod * Working through the access hole remove the outside door handle retaining bolts * Remove the handle/lock cylinder assembly from the car

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you replace the inside door handle on a Hyundai elantra?

How_do_you_remove_a_door_panel_and_handle_to_repair_the_window_in_a_'00_Hyundai_Elantrathis might help..


How do you replace door handle 2003 elantra?

To replace the door handle on a 2003 Hyundai Elantra, first, remove the interior door panel by unscrewing any screws and gently prying it off. Next, disconnect the door lock and handle linkage from the old handle. Remove the retaining screws or clips holding the handle in place, then replace it with the new handle, reassemble the linkage, and put the door panel back on. Finally, test the new handle to ensure it functions properly.


How do you replace the driver side exterior door handle on a 1998 Hyundai Accent?

take it out


In a 2000 Hyundai elantra you have every gear exept overdrive what could be the problem?

Could be the overdrive on/off switch, which is located on the gearshift handle. That's all the help I can give you, best of luck.


How do you replace an interior door handle on a Hyundai?

The interior door handle on a Hyundai latches onto the locking mechanism of the door. First remove the old handle by unscrewing it from the door panel. Pull the handle out and remove the locking wire. Install the new unit with the locking mechanism in place. Tighten the mounting screw.


Where is the transmission fluid dipstick located on a 2008 Hyundai Elantra?

On a 2008 Hyundai Elantra, the transmission fluid dipstick is located towards the back of the engine bay, near the firewall. It's typically found near the transmission itself, and it may be identified by a colored handle, often yellow or red. To check the fluid level, make sure the engine is running and the car is in park or neutral.


How can you replace a door handle on a 2003 Hyundai Tiburon?

The 2003 Hyundai Tiburon has door handles that sometimes break or need replaced. They can be easily removed and replaced with a new part.


How do you replace exterior driver door handle on 2001 Hyundai elantra?

* To remove the outside door handle and lock assembly raise the window and remove the door trim panel and watershield * Working through the access hole disengage the plastic clips that secure the outside handle to latch actuating rod and the outside door lock to latch actuating rod * Working through the access hole remove the outside door handle retaining bolts * Remove the handle/lock cylinder assembly from the car


How do you remove grab handle on a Hyundai tiburon?

To remove the grab handle on a Hyundai Tiburon, first, locate the screws securing it to the ceiling. Use a screwdriver to remove these screws. Next, gently pull the handle away from the mounting area, ensuring not to damage any clips or wiring. Once detached, you can replace or repair the grab handle as needed.


How do you replace a 2001 Hyundai elantra front outer door handle?

1. Raise the window and remove the door trim panel and water shield 2. Working through the access hole disengage the plastic clips that secure the outside handle-to-latch actuating rod and the outside door lock-to-latch actuating rod 3.working through access hole remove the outside door handle retaining bolts 4. Remove the handle/lock cylinder assembly from the vehicle


How to remove Window crank in a 2004 Hyundai accent?

Make your life easy and just break off the door handle. When you are finished with your project, just replace the door handle with a new one from the dealer.


How do you wire a trailer connector for a 2003 Hyundai Elantra?

I have read that you need a "powered" wiring harness because the Elantra routes the tail lights through a computer that cannot handle the extra amperage necessary to drive a trailer's lights. A powered harness connects directly to the battery for power and taps the tail-light wires to control relays.