0
How do you replace the rear suspension member assembly insulator on a 1986 Nissan 300ZX?
When we replaced ours we used a hammer and chisel to remove the original sleeve in order to install the new polyurethane sub-frame mounts. I found them online at www.thezstore.com. Apparently the original rubber ones required the sleeve and the replacement ones don't. We found this out by searching for images to verify this information
Subframe Bushing Kit, 84-89 300ZX.Quantity in Basket:noneCode: 23-4148
Price:$42.95
I hope this helps and you are able to enjoy your z car more!
What else can I help you with?
How do you replace the Wheel Hub Assembly in a 1999 Nissan Maxima?
To replace the wheel hub assembly on a 1999 Nissan Maxima, first, lift the vehicle and remove the wheel. Disconnect the brake caliper and rotor, and then remove the axle nut. Next, unbolt the hub assembly from the suspension and pull it out, then install the new hub assembly in reverse order, ensuring all bolts are torqued to specifications. Finally, reattach the wheel and lower the vehicle.
How do you repair a front drive axel on a 1999 Nissan Altima?
you will have to remove the wheels/ rotor and hub assembly , buy a set of new axels from Nissan or after market auto parts and replace the old ones..not recommended unless you have knowledge on suspension work
How do you replace the tail light assembly on a 2002 Nissan Sentra?
Soak it in lube.
How do you replace rear wheel bearings in Maxima 2004?
Can figure out how to remove rear rotor assembly to replace wheel bearing assembly on a Maxima 2004 Nissan
How do you replace the taillight bulb on a Nissan Armada?
Remove the taillight assembly to gain access to the bulbs
How do you replace strut mounts on a 1996 Nissan 200sx?
To replace the strut mounts on a 1996 Nissan 200SX, start by safely lifting the vehicle and removing the front wheels. Next, detach the strut assembly by unscrewing the bolts connecting it to the steering knuckle and the top mount under the hood. Replace the old strut mount with a new one, reassemble the strut assembly, and ensure all bolts are tightened to the manufacturer's specifications before reinstalling the wheels and lowering the vehicle. Always check the alignment after replacing suspension components.
How to convert Nissan computer controlled suspension to standard shocks?
In most cases when switching from Electronic to standard suspension you need to get the complete assembly from a non electronic suspension and put it it. This will work in MOST cases because the car body itself doesn't change only the suspension unit.
How do you replace the headlight bulb located on a 2000 Nissan Altima?
go to back of headlight assembly and twist it out.
How do you replace taillight assembly in a 2004 Nissan Titan with a factory bedliner?
Figured it out. OPen the Tailgate and look!
Can you replace The rear wheel bearing or do you have to replace the entire wheel hub assembly on a 2000 Nissan Maxima?
I have 1997 Nissan Maxima. You ned to replace the entire hub assembly. My problem is that they discontinued the 1997 hub assembly and the suggested replacement part's ABS ring is 4MM taller therefore the ABS sensor cannot clear the ABS ring. Any ideas on this one?
How do you replace the tail light assembly on a 2006 Nissan Titan?
To replace the tail light assembly on a 2006 Nissan Titan, first, open the tailgate and remove the screws securing the tail light assembly using a socket wrench or screwdriver. Carefully pull the assembly out from the vehicle and disconnect the wiring harness. Replace it with the new assembly by reconnecting the wiring harness and securing it with the screws. Finally, test the new tail light to ensure it functions properly before closing the tailgate.
How do you change headlight assembly on a 2006 Nissan Maxima?
To change the headlight assembly on a 2006 Nissan Maxima, first, open the hood and locate the headlight assembly you need to replace. Remove the screws or bolts securing the assembly, and disconnect the wiring harness. Carefully pull the assembly out and replace it with the new one, reconnect the wiring, and secure it with the screws or bolts. Finally, test the headlight to ensure it's functioning properly.
