0
What else can I help you with?
Is there a certain order to tighten the bolts when replacing the transmission in a 1998 buick lesabre?
No
What order do you tighten valve cover bolts on a 2005 5.4?
[object Object]
What are the torque specifications for Subaru EJ25 cylinder head bolts?
According to the manual for a EJ25 SOHC:Bolt sequence:____| C A F || E B D |-----B: INSTALLATION1) Install the cylinder head and gaskets on cylinder block.CAUTION:• Replace cylinder head gaskets with new ones.• Be careful not to scratch the mating surface of cylinder block and cylinder head.2) Tighten the cylinder head bolts.(1) Apply a coat of engine oil to the washers and bolt threads.(2) Tighten all bolts to 29 N·m (3.0 kgf-m, 22 ftlb) in alphabetical sequence.(3) Tighten all bolts to 69 N·m (7.0 kgf-m, 51 ftlb) in alphabetical sequence.(4) Back off all bolts in reverse order of assembly by 180° first; back them off by 180° again.(5) Tighten bolts A and B to 34 Nm and bolts C-D-E-F to 15 Nm(6) Tighten all bolts by 90°(7) Tighten all bolts a further 90°CAUTION:Do not tighten bolts more than 90° in total angle
What is the torque for the head gasket of a '93 dodge shadow and what is the order to tighten the bolts?
10 6 1 2 7 9 5 4 3 8 tighten in that order when tightening turn one quarter turn then torque to 65 in that above order and then tighten to 65 in that order again
What are the cyl. head bolt torque specs for a KIA 1.8 L 2000?
Hello: Install cylinder head bolts. Tighten cylinder head bolts according to following procedure: Tighten cylinder head bolts in order shown, Can not show diagram for this. Tightening torque : 36.1 lb-ft (49N
What is the tightening order for Chevy intake?
to tighten a intake manifold start with a center bolt and tigten in a circular pattern towards the ends. tighten bolts in even incraments until tight.
What sequence do you tighten up head bolts on a KIA Sedona 2.9crdi 2003?
To tighten the head bolts on a 2003 KIA Sedona 2.9 CRDi, follow a specific sequence to ensure even pressure. Start from the center bolts and work your way outward in a spiral pattern. Typically, the sequence is to tighten the bolts in the order of 1-5-3-7-2-6-4-8 (if numbered in a specific layout). Always refer to the manufacturer's service manual for the exact specifications and torque values for the bolts.
1980 Pontiac transam 5.0 what the order in which you tighten the cylinder bolts?
ask autozone ask autozone try keyword autozone
What is the torque specs for head bolts on a 2000 Pontiac sunfire?
This is right from the good old Hayne's manual. (All numbers are in Ft./Lbs) STEP ONE: Tighten Short bolts - 43 Tighten Long bolts -46 STEP TWO Tighten an addditional 90 degrees Bear in mind that there is a specific tightening order which is just too complicated to explain here. Buy a Haynes manual for more exact instructions FriPilot
Cylinder head torque settings for a 1997 punto s 60?
Head bolts for a Punto 60s need to be tightened in 3 stages: stage 1 - tighten all bolts (in the correct order!) to 30Nm. stage 2 - tighten again, in same order as before, by turning wrench a further 90 degrees stage 3 - repeat stage 2
1986 Nissan PU valve cover gasket. is there a certain order to tighten bolts?
standard star works just fine, be careful not to overtighten
Do you have to take apart the rocker arm assembly when replacing head gasket on a 1993 ford explorer?
no the head separates from block the valve cover comes off the head bolts are under that and take them out and pry head up and then replace head gasket then repeat the order put head back on and tighten bolts and be sure not to scratch the head gasket when you put the head back on
