0
First, you want to locate the red colored lock on the housing connector, just give it a small push and it should you feel it slide over to one side. It is now unlocked. Next you want to see where the neon green connector is slipped over 2 small prongs on the oil pressure unit. Pry those up a bit and as you are holdin them pull and wiggle the neon green connection off of the pressure unit and over the small prongs. Be carefull as sometimes the housing is weak from heat and might crack.
What else can I help you with?
Changing oil pressure switch on 1996 Audi A4?
Audi A4 1999 1.9TDi Oil pressure light on continously. Engine sounds fine. How do I remove electrical connector to remove switch and check pressure with a gauge?
How do you remove the oil pressure switch on a 2005 ford f150 truck 4 by 4?
unplug electrical connector then put a wrench on it and unscrew it
Where is the Oil pressure sensor on 1996 sunfire?
Engine Oil Pressure Sensor and/or Switch Replacement == J 35749 Oil Pressure Switch Socket # # Remove the air cleaner outlet resonator. # Disconnect the oil pressure electrical connector. # Remove the engine oil pressure sensor (1) usingJ 35749 . # # Install the engine oil pressure sensor (1) using J 35749 . # Connect the oil pressure electrical connector. # Install the air cleaner outlet resonator.
How do you replace the passenger side mirror on a 2005 Ford Focus?
Removal and Installation Remove the trim panel. Release the clip. Release the locating tabs. Remove the trim panel. Disconnect the exterior mirror control switch electrical connector. Disconnect the exterior mirror electrical connector. Release the clip. Release the electrical connector. Disconnect the electrical connector. Remove the exterior mirror. Remove the bolt. If equipped, remove the screw. To install, reverse the removal procedure.
Explain step by step how to put in the blower resitor?
Remove the electrical connector from the old resistor. Remove the screws holding the resistor in place. Remove the old resistor. Put in the new one and screw in the screws. Attach the electrical connector.
How do you replace egr valve on a 2001 pt cruiser?
To replace the EGR valve on a 2001 PT Cruiser, first, disconnect the negative battery terminal to ensure safety. Remove the vacuum hose and electrical connector from the EGR valve, then unbolt the valve from its mounting position using a wrench. Clean the mounting surface to remove any old gasket material, then install the new EGR valve with a new gasket, reconnect the electrical connector and vacuum hose, and finally reconnect the battery terminal. Start the engine to ensure the new valve functions properly.
How do you remove crank sensor on a 2000 Dodge Intrepid?
Disconnect the electrical connector, remove the mounting screw and remove the sensor.
How do you replace the fuel pressure sensor on a 2005 Mazda Tribute?
To replace the fuel pressure sensor on a 2005 Mazda Tribute, first, ensure the vehicle is off and disconnect the negative battery terminal to prevent any electrical issues. Locate the fuel pressure sensor, which is typically found on the fuel rail. Remove the electrical connector and use a wrench to unscrew the sensor. Install the new sensor by screwing it in place, reconnecting the electrical connector, and finally reconnecting the battery terminal.
How do you replace the fuel pressure sensor on a 2006 Ford truck?
To replace the fuel pressure sensor on a 2006 Ford truck, first, ensure the ignition is off and disconnect the battery to avoid electrical issues. Locate the fuel pressure sensor on the fuel rail, typically at the end of the rail near the injectors. Carefully unplug the electrical connector and use a wrench to remove the old sensor. Install the new sensor by threading it into place, reconnect the electrical connector, and then reconnect the battery.
How do you replace tail light assembly in 2000 Toyota Land Cruiser?
To replace the tail light assembly in a 2000 Toyota Land Cruiser, start by opening the rear hatch and removing the screws or bolts securing the tail light assembly. Carefully pull the assembly out, disconnect the electrical connector, and remove the old assembly. Install the new tail light by connecting the electrical connector, positioning it in place, and securing it with the screws or bolts. Finally, test the new tail light to ensure it functions properly before closing the hatch.
How do you remove speakers 2007 model mustang?
Door Speakers: * Remove the door trim panel * Remove the speaker mounting screws * Pull out the speaker and disconnect the electrical connector from the speaker and remove the speaker Door Subwoofers: * Remove the subwoofer grille trim panel * Remove the door trim panel * Remove the 8 mounting screws from the front side of the subwoofer * Remove the single subwoofer retaining screw from the backside of the subwoofer enclosure * Pull out the subwoofer,disconnect the electrical connector and remove the subwoofer Quarter Panel Speakers: * Remove the quarter panel trim * Remove the 4 speaker mounting screws * Pull out the speaker,disconnect the electrical connector and remove the speaker Parcel Shelf Speakers: * Working from inside the trunk area,disconnect the speaker electrical connector * Remove the parcel shelf * Remove the speaker mounting screws and remove the speaker
How do you change fuel tank pressure sensor in 2000 Pontiac Grand Prix GTP?
To change the fuel tank pressure sensor in a 2000 Pontiac Grand Prix GTP, start by relieving the fuel system pressure and disconnecting the negative battery cable. Next, remove the fuel tank by unbolting it and lowering it carefully, then locate the pressure sensor on the top of the tank. Disconnect the electrical connector and remove the sensor from its mounting. Install the new sensor, reconnect the electrical connector, and reassemble the fuel tank, ensuring all connections are secure before reconnecting the battery.
