0
What else can I help you with?
What is the size of the socket for bolts on a valve cover for a 95 dodge neon?
10mm or 12mm metric 10mm or 12mm metric
What is the torque value for the valve cover gasket on a 2000 Toyota Camry 4-cylinder?
According to Chilton's, the Specification for the Spark Plug Tube Nuts, Which bolts the valve cover on, is 33 lbs. The socket size is 30mm. However, I was told by a friend of mine who is a mechanic that he tightens them at 20 lbs.
How do you change a valve cover gasket on a 1989 beretta GT?
First locate the valve cover. If the motor is a 4 cylinder there will only be one valve cover. If it is a 'v6' it will have two as well as v8 automobiles. With a Socket wrench and extention locate the valve cover bolts that go around the cover bolting it to the top of the engine (cylinder head.) Usually the valve cover will have the 'Oil Filler' cap on it. (Where you add oil to the engine...) With the correct size socket remove the bolts that hold down the valve cover. Lift the valve cover up and away from the cylinder head. You may need to strike it with a soft mallet to get it to release. Once it's off you will see the rockers/springs. Be careful to keep the old gasket debrey from entering the rocker valley. With a razer scrap all remaining gasket from the cylinder head. Some gaskets have an "UP" side so make sure you look over your gasket for any indicators. Then apply your new gasket. Then put your valve cover back on carefully so your new gasket does not move. Slide the bolts back into place and tighten from the middle out. Tighten the bolts until they just about snug then move to the next opposing bolt. So Center, Bottom Center, Left, Bottom Left, Right, Bottom Right etc. Once they are all snug go back and turn the wrench another half turn to tighten them up. *Do Not Over Tighten The Bolts.* or damnage to the gasket or bolt breakage may occur. If oil leaks from the cover check for loose bolts or gasket breakage. Edit by Loosenut: Torque spec is 12lbs. for the valve cover bolts.
Where does it say the size of the engine on the engine?
Generally on top on the valve cover or engine cover.
How do you tell a 305 from a 350?
on the vin coad its the eighth diget on the vin plate if you dont have a vin if your valve covers bolt in the middle with 4 bolts it is a 305 if they bolt on the edges 4 bolts then it is a 350 That answer is wrong. A 350 has a 4" bore. A 305 has a smaller bore. All SBC made after 1986 have the center bolt valve covers, no matter what size motor it is. All pre-86 SBC have perimeter valve cover bolts.
Where is the PCV valve located on a 2004 Chevrolet Malibu?
You did not say what size engine but in most cases the PCV valve is in the valve cover.
What does numbers on a ford v8 engine valve cover mean?
size of motor
What size are derby cover bolts?
1/4 20 x 5/8
What size bolts are holding a 2002 Toyota iac valve?
The idle air control (IAC) valve on a 2002 Toyota typically uses bolts that are 10mm in size. The exact length may vary depending on the specific engine model, but they are usually standard metric bolts. It's recommended to check the vehicle's service manual for the precise specifications and torque settings when replacing or reinstalling the IAC valve.
Where is the PCV valve on a 2004 Ford Freestar?
This will depend on the engine size. If it's a 3.0L then it's location in the right rear valve cover next to the firewall. All others have it in the left front valve cover.
Where is the Ignition Coil on a 2004 Dodge Neon motor size 2.0?
It is on top of the valve cover.
Where could oil be leaking from on the top side of the engine of a 1997 Pontiac grand am se?
It depends on you size of your engine, if its on like the left side of a 4 cylinder it could be the timing chain housing gasket or bolts loose or damaged, or in the front or back on the V6 it could be the Valve cover gasket or bolts loose or damaged
