0
What else can I help you with?
Where is the torque converter on a 1999 Buick Le Sabre?
The torque converter is between the engine and transmission.The torque converter is between the engine and transmission.
How much torque does a 200 cc two stroke gas engine have?
The torque of a 200 cc two-stroke gas engine typically ranges from about 10 to 15 Nm (Newton-meters), depending on the specific design and tuning of the engine. Two-stroke engines are known for their high power-to-weight ratio, but they usually produce less torque compared to four-stroke engines of similar displacement. Factors such as the engine's configuration, intended use, and performance tuning can significantly influence the exact torque output.
Is yezdi a 2 stroke engine bike?
yes it is absolutely a two stroke engine since it develops an amazing power and torque. this credit completely goes to cz two stroke engine which is unaparalleled in the world.
What is the difference between a two stroke dirtbike and a four stroke?
A 4-stroke will run quieter and cleaner. It will rev lower. For a given engine power it'll be heavier and bigger. For a given engine power it'll use less fuel. The engine will need more parts and be more complicated 4-strokes generally have better torque at low revs. A 2-stroke will run noisier and pollute more, It will rev higher, for a given engine power it'll be smaller and lighter. For a given engine power it'll use more fuel. The engine will consist of fewer parts, and be a simpler design. 2-strokes generally have less torque at low revs but do better at high revs.
What is difference between torque at Nm equals 120 rpm equals 1800 and Nm equals 120 rpm equals 4000 give detail better as performance and load capacity in petrol engine?
Difference between Torque and load
Torque specs for injectors for 7.3 power stroke engine?
120 Inch Lbs
Why two stroke engines are hi-speed engines and four stroke engines are hi-torque engines?
generally , two strokes are smaller capacity , shorter stroke, higher revs. for given engine capacity , long stroke /small bore = high torque / low revs short stroke/big bore = low torque / high revs
What is the difference between power and torque?
In simple terms, torque gets you moving and power keeps you moving. In other words, your acceleration is dictated by the torque your engine provides and the top speed is limited by the power.
What is the torque specs for Head bolts for 2003 Johnson 4 stroke 140 hp?
What is the torque specs for Head bolts for 2003 Johnson 4 stroke 140 hp outboard boat engine
Difference between horsepower and torque?
Torque is the measurement of turning force. A wrench applies torque to a bolt. A motor or engine provides torque to do work. Horsepower is the measurement of the work done or ability to do work. This is done by taking the speed the engine is operating at (RPM) and what torque it is producing and applying a formula to give a horsepower rating.
What is the difference between a single-acting and an opposed piston engine is?
Single-acting? You mean like a single cylinder engine, like in my lawn mower? The biggest difference (besides the obvious "an opposed engine has more cylinders" is that an opposed engine has more torque. On a single-cylinder four-stroke, you've got the cylinder moving under input energy--the burning gasoline--for one stroke, and under stored energy from the flywheel for three strokes. If you have a two-cylinder engine, you have two strokes where the engine is moving under input energy--each cylinder has one--and two strokes using stored energy. If you have a four-cylinder engine, each stroke is moving under input energy.
Verify the difference between a long vs a short connecting rod - lets assume bore is 4 and stroke is 3 -what efffect would it have horsepower torque?
long rod=more stroke and more torque The above is a common misconception. Stroke is determined by the "throw" of the crankshaft. The rod length only determines how high the piston travels into the cylinder. You'll need to match the rod to the piston so that the piston doesn't hit the cylinder head at the top of the stroke or the crankshaft at the bottom of the stroke. But think about it. The total stroke is not determined by the rod, but by by the difference between the crankshaft center at the top of the stroke versus the bottom. EDIT: Can i see some mathematical formula (with trig) with the example if possible PLEASE ! Thanks guys
