0

Subjects>Auto>Asian Cars

What is the minimum brake rotor thickness for a Mazda 3?

Anonymous

∙ 12y ago

Updated: 10/23/2022

23mm front 9mm rear

Wiki User

∙ 12y ago

What else can I help you with?

Related Questions

What is the minimum brake rotor thickness for a 2001 Pontiac grand am gt?

The 2001 Pontiac Grand Am minimum brake rotor thickness is .075. The minimum brake rotor thickness is a standard minimum. Certified mechanics cannot use the brake rotor when the thickness drops below this level.

Minimum thickness Mazda 626 1998 brake rotors?

For a 1998 Mazda 626 the minimum thickness is .866 inches for the front rotor and .315 inches for the rear rotor. This is the same for the 4 and 6 cylinder versions.

What is the minimum thickness of brake rotors?

It is the safe and legal minimum thickness allowed for a brake rotor.

What is the minimum brake rotor thickness on my Ford Explorer and what is the thickness when new?

2004 ford explorer minimum rotor thickness

What is the minimum front brake rotor thickness for 1998 Chrysler sebring jxi?

The minimum front brake rotor thickness is three aids of an inch. When the rotor does not have the minimum thickness the auto mechanic replacing the brakes can not use the rotor.

What is the minimum rear brake rotor thickness for 1996 Lexus LS400?

The minimum rear brake rotor thickness on a 1996 Lexus LS400 is 15mm.

2003 Mazda protege 5 brake rotor thickness?

Front: 24mm new, 22mm minimum Rear: 10mm new, 8mm minimum

What is the minimum front and rear brake rotor thickness for a 2002 Ford F-350?

The minimum thickness is cast into the rotor, either on the edge of the rotor or into the rotor hub.

What is the minimum thickness for a Mazda 6 rear rotor?

8mm

What is the minimum brake rotor thickness for a 2006 Lexus gs?

The minimum disc brake rotor thickness specifications for the 2006 Lexus GS are:Front: 27mmRear: 16.5mm

Minimum brake rotor thickness for a 2003 Mitsubishi Eclipse GTS?

The brake rotor thickness for your 2003 Mitsubishi Eclipse, is 0.75. The rotor should not be used if the thickness is less than this.

What is the minimum brake rotor thickness for a 2003 Ford Ranger?

It is important to maintain your brakes properly. The minimum brake rotor thickness for a 2003 Ford Ranger is 0.99 inches.

Trending Questions

Is 20'' Rims 2 big for a Honda Accord? How many gallons does the gas tank in the 2011 Lexus IS-250 hold? How do you open the hood on your 1990 Lexus when the hood latch cable is broken? How do you change a dash light for a 1998 Corolla? Pulling a transmission fill plug out of a Isuzu trooper? Where is the pcv value on 1980 Nissan truck? How do you remove the back seat of a 1988 Honda Accord DX? What is the towing capacity of a 1999 Chevrolet pickup with 5.7L? How do you change the rear right brake light bulb on a Mitsubishi eclipse 2001? Is it possible to convert a car made in Japan with a right hand drive to a left hand drive for in the US and how much? Where is the 1998 eclipse fuel pump relay located? Why would an odometer on a 1995 Nissan 200SX SE with a working speedometer and new speed sensor work when the engine is cold winter mornings but not work after the engine warms up? How do you replace a headlight socket for an Isuzu Ascender? How can you make your car flat on water? Why doesn't my 1996 Acura TL start? How to remove the front strut on a Honda accord without removing the tire? Hyundai santa fe radio color codes looking for steering wheel control wire color? Were is the crank shaft position sensor on a 2002 Kia rio? Does a Kia Sedona 2.9 liter diesel have a timing belt? I replaced my battery in my 1993 Toyota Previa and don't remember my radio code Is there an override code?

Resources

Top Categories

Product

Company

Copyright ©2025 Answers.com. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Answers.