0
44-78 in-lbs. Mazda manual recommends tightening the bolts in the following pattern (recommend lightly tightenint each bolt in 3 cycles):
- Center bolt between 2nd and 3rd spark plug.
- Center bolt in front of spark plug #1.
- 4 bolts down the driver's side, starting from front to back (timing belt to firewall)
- Center bolt behind spark plug #4.
- 4 bolts down passenger's side starting from back to front (firewall to timing belt)
- Center bolt in front of spark plug #1.
- Center bolt between 2nd and 3rd spark plug.
- Center bolt behind spark plug #4.
What else can I help you with?
What is the valve cover torque on a 2000 Mazda Protege 1.8L?
The 2000 Mazda 1.8 liter engine valve cover torque specification is 45 pounds. The valve cover bolts should be torqued in 15 pound intervals.
What is the torque for Valve cover bolts for 1990 Mazda Miata?
The torque specification for the valve cover bolts on a 1990 Mazda Miata is typically around 7.2 to 9.0 ft-lbs (or 10 to 12 Nm). It's important to follow a proper sequence when tightening to ensure an even seal. Always refer to a service manual for the most accurate specifications and procedures.
What is the clutch cover bolts torque Specification on a 2001 Ford F-150 XL?
35 ~ 46 Foot pounds of torque. Pressure plate bolts.
What is torque spec for 2001 altima valve cover?
The 2001 Nissan valve cover bolt torque specification is 45 pounds. The valve cover bolts should be torqued in 15 pound intervals.
What are the valve cover torque specs for a 2001 3.0 Mitsubishi Montero Sport?
The 2001 Mitsubishi Montero Sport 3.0 liter engine valve cover torque specification is 40 pounds. You do not want to over torque the valve cover bolts, as you may ruin the valve cover gasket.
What is the torque level for valve cover gasket on 1989 mercury topaz 2dot3l?
The torque specification for the valve cover bolts on a 1989 Mercury Topaz 2.3L is usually around 35 inch-pounds. It is recommended to tighten the bolts in a crisscross pattern to ensure even distribution of torque and to prevent leaks.
What are the torque specs for a 94 sc2 valve cover gasket?
89inch pounds is the torque rating for the valve cover bolts
What is torque specification for 2002 ford 3.0 dohc valve cover?
I was told 7lbs
What is the valve cover torque specification for a 1995 Dodge Dakota 3.9?
95 in-lbs.
What are the torque specifications for a 1997 Audi 2.8 valve cover and oil pan?
For a 1997 Audi 2.8, the valve cover bolts typically have a torque specification of around 7-10 Nm (5-7 lb-ft). For the oil pan, the torque specification is generally around 10-15 Nm (7-11 lb-ft). It's important to follow a specific tightening sequence and to check the manufacturer's service manual for any updates or specific procedures. Always ensure that the bolts are torqued in a gradual manner to avoid warping the components.
How do you torque a valve cover on a Toyota Previa?
To torque a valve cover on a Toyota Previa, first ensure that the engine is cool and the valve cover is clean. Use a torque wrench to tighten the valve cover bolts in a crisscross pattern to ensure even pressure. The recommended torque specification is typically around 7.2 to 9.0 ft-lbs (10 to 12 Nm), but it's best to consult the specific service manual for the exact specifications. Always double-check the torque after the initial tightening to ensure proper sealing.
What is the valve cover torque specification for a Jeep CJ7 1985?
6-8 lb/ft.
