0
What else can I help you with?
Where is the crankshaft position sensor in a 2003 Mitsubishi Galant?
On the 2.4 and 3.6 liter engines it is behind the timing cover down by the crankshaft sprocket. Caution: the timing belt cover bolts of varying lengths. Be sure to mark the bolts and the cover to return them to the proper holes. You may wish to change timing belts while you are in there.
How do you replace a timing chain on a 2007 Mazda 6 2.3 liter?
What are the timing marks for 2.3 2007 mazda 6
Does a 2005 Mazda tribute have a timing chain or a timing belt?
Timing CHAIN ( 2.3 liter 4 cylinder and 3.0 liter V6 engines )
Does a 2000 Mazda B4000 4 liter V6 have a timing belt or timing chain?
timing chain
Does a 1999 Mazda 2.5 liter have a timing belt?
Yes
How to time a 1999 Mitsubishi mirage 1.5 liter?
To time a 1999 Mitsubishi Mirage with a 1.5-liter engine, first ensure the engine is at TDC (Top Dead Center) for cylinder one by aligning the timing mark on the crankshaft pulley with the corresponding mark on the timing cover. Next, check the alignment of the camshaft sprocket; the timing mark should be aligned with the mark on the cylinder head. If necessary, adjust the timing belt to ensure both the crankshaft and camshaft marks align correctly. Finally, reassemble any components and start the engine to verify proper timing.
What are the timing specs for a 1997 Pontiac Grand Am 2.4 liter quad 4?
The timing is ground in the crankshaft and not adjustable.
Does the 2005 Mazda 6 have timing belt or chain?
Timing CHAIN ( 2.3 liter 4 cylinder and 3.0 liter V6 engines )
Does 2008 Mazda 6 use a timing belt or timing chain?
chain ( on the 2.3 liter 4 cylinder and the 3.0 liter V6 )
Does a 2009 Mazda 3 has timing belt or chain?
2.0 liter
Does a 1994 Mazda mx6 have a tming belt or timing chain?
On a 1994 Mazda MX-6 : Both the 2.0 liter four cylinder engine and the 2.5 liter V6 engine have a timing BELT
Where would the timing marks on a 96 Mazda millenia would be?
Installing the timing belt on a Millenia. I have a Mazda Millenia with a 2.5 liter engine that I just replace the timing belt and tensioner on. In the explanation left and right are in reference to how you are looking at the engine. The timing marks are hard to find. Above the crank sprocket, there is an upside down triangle cast into the block. Behind the crank sprocket, there is a flat disc that rotates with the sprocket. This disc has a notch in it that needs to be lined up with the upside down triangle. Looking at the front of the engine, the camshaft to your right has an arrow on the sprocket. Line this up with the very small tick cast into the block. This should line up the arrow at about a 10:00 o'clock position. On the camshaft located on your left, the original factory tick mark for timing can't be seen without a mirror when the engine is in the vehicle. So, as an afterthought, Mazda came up with another solution. There are two tick marks on the block at about the 12:00 o'clock postion. On the camshaft sprocket are two small drilled out holes that need to line up with these two tick marks. If you haven't already, the hydrolic tensioner needs to be removed, compressed, pinned, and reinstalled. Then remove the idler pulley just below the camshaft sprocket located to your right. Route the belt over the crankshaft, right side idler pulley, right side cam sprocket, tensioner idler, and then left side cam sprocket. While putting tension on the belt, reinstall the missing idler pulley. Then remove the pin from the tensioner releasing tension on the belt. Rotate the crankshaft twice and recheck the timing.
