Press the "ADJ" and "ST/STP" buttons simultaneously. This will allow you to turn on/off the hourly chime (indicated with a CH icon), as well as activate/deactivate the alarm mode.
To change an Armitron WR330 watch back to standard time from military time, press and hold the SET button until the display flashes. Then use the MODE button to scroll and find the 12/24-hour setting. Use the ADJ button to switch between 12-hour and 24-hour formats, then press SET to confirm and exit the setting.
To switch the date and day display on the Armitron WR330, you usually need to press and hold a specific button (sometimes labeled as SET or MODE) until the date or day starts flashing. Once it is flashing, you can then use the other buttons to navigate and change the setting accordingly. Check the manual for specific instructions as the process can vary by model.
YOU HAVE TO STAND UP . ON ONE LEG. ( TIME DOESNT EXIST ) YOU MAKE A 360 TURN . CLOSE YOUR EYES. YOU TAKE A DEEP BREATH. AND YOU THINK WHAT TIME YOU DESIRE TO BE ON CLOCK. ETIMOP
The "WR 165" is not the model number; it only indicates that the watch is water resistant to 165 ft.I have the Armitron 45/6967 (model number found on the back) and there are no instructions anywhere online. Even if you have a different watch maybe this will help.Abridged instructions for the Armitron 45/6967:A /set adj\ BC \mode EL/ D (light)To set the Alarm/ Time/ Date:1) Alarm: Push and hold C- the first mode is to set the alarm.A switches between hours and minutes indicated by the numbers flashing.B advances the hours and minutes.2) Time & Date: Push and hold C (to set alarm) push C again to set the time & date indicated by the seconds flashing. What is flashing is what will be adjusted.*This mode starts with seconds, Pushing A cycles through Time and Date.Pushing A (number of times) takes you to:(1) minutes, (2) hours, (3) month, (4) date, (5) day of the week.Pushing A again will take you back to the start with seconds so if you miss what you want to adjust just cycle through until you come back around.B advances whatever is flashing (except seconds, it just zeros it out). If you are in 12-hour mode PM is indicated with a P above the minutes; AM is blank.To turn on/ off the Alarm and Hourly Chime:1) Push and hold B- this will tell you what time the Alarm is currently set to go off. *Note this is not how to set the alarm, see aboveWhile still holding B push A to turn on/ off the alarm and hourly chime.What is on is indicated on the bottom of the display:----> ALCH ALCH
The "WR 165" is not the model number; it only indicates that the watch is water resistant to 165 ft.I have the Armitron 45/6967 (model number found on the back) and there are no instructions anywhere online. Even if you have a different watch maybe this will help.Abridged instructions for the Armitron 45/6967:A /set adj\ BC \mode EL/ D (light)To set the Alarm/ Time/ Date:1) Alarm: Push and hold C- the first mode is to set the alarm.A switches between hours and minutes indicated by the numbers flashing.B advances the hours and minutes.2) Time & Date: Push and hold C (to set alarm) push C again to set the time & date indicated by the seconds flashing. What is flashing is what will be adjusted.*This mode starts with seconds, Pushing A cycles through Time and Date.Pushing A (number of times) takes you to:(1) minutes, (2) hours, (3) month, (4) date, (5) day of the week.Pushing A again will take you back to the start with seconds so if you miss what you want to adjust just cycle through until you come back around.B advances whatever is flashing (except seconds, it just zeros it out). If you are in 12-hour mode PM is indicated with a P above the minutes; AM is blank.To turn on/ off the Alarm and Hourly Chime:1) Push and hold B- this will tell you what time the Alarm is currently set to go off. *Note this is not how to set the alarm, see aboveWhile still holding B push A to turn on/ off the alarm and hourly chime.What is on is indicated on the bottom of the display:----> ALCH ALCH
Depending on how loud your alarm is,it is possible that it may set off another cars alarm.
You can set the alarm off by just simply jumping on the car.
Any type of smoke, steam or particles denser than air will set off a smoke alarm. This means that smoke emitted from the incense will set off a smoke alarm when in range of the detector.
The best way to reset an Armitron 40-8249 is to take it to a watchwaker or jeweler who knows the equipment. Armitron does have a detailed manual available on their website, however.
If you set the alarm (i.e. lock the car) and then disconnect the battery, the alarm will go off. If you disconnect the battery when the alarm is not set (i.e. when the car is unlocked) the alarm will not go off. (So don't try to nick a locked one).
Isn't it obvious...
No