0
What else can I help you with?
What color is the memory wire on a kenwood dnx9990hd?
copper
89-Nissan Maxima Radio wire color code?
WHAT ARE"89-NISSAN MAXIMA RADIO WIRE COLOR CODES
What is the brown wire and the blue wire with the white stripe for on a kenwood kdc mp205 car stereo?
brown wire is called earth wire .or blue wire with white stripe is for anteena wire ok
How do you bypass e brake on kenwood KVT-512?
Ground the green wire on the harness.
Color wire for a Kenwood VZ907?
The memory wire is blue on the Kenwood VZ907. Now I hope you can help me. I am trying to hook this same product in my vehicle. However, I cannot get past BUS-E50. What does this mean? The memory wire is blue on the Kenwood VZ907. Now I hope you can help me. I am trying to hook this same product in my vehicle. However, I cannot get past BUS-E50. What does this mean?
How do you unlock your kenwood kvt-725-b in car DVD player?
kvt725 b i her the movie but not see there should be a wire for connecting to your handbrake switch so you can only watch images when the vechile is stoped, on ripspeed DVD players this wire is pink and you earth the wire to make the screen work, this maybe the case for your kenwood.
How can the loose wire of a starter on a 97 Nissan Maxima be fixed?
If the wire is loose at a connection, find a wrench that will fit it and tighten it.
Should there be electricity to coil 1999 Maxima?
When the key is turn on there should be 12.5 volts on one wire (there are three wires). There is also a ground wire and a wire from the ECM for the transistor.
Where do you connect the light green wire to on a kenwood?
The light green wire on a Kenwood car stereo is often used for the parking brake detection. It should be connected to a ground source to bypass the parking brake safety feature on the stereo, but please make sure to check local laws and regulations regarding this before attempting to bypass it.
What are car stereo wiring color codes for a kenwood?
Red - +12v Ignition/Switched Yellow - +12v Battery/Constant Black - Chassis Ground Blue - Power Amplifier Blue/White - Power Amplifier Remote +++++++++++SPEAKERS+++++++++++ Green - LR+ Green/Black - LR- Violet - RR+ Violet/Black - RR- White - LF+ White/Black - LF- Grey - RF+ Grey/Black - RF-
Have a 1997 jeep grand Cherokee with infinity gold system trying to install a ken wood deck bought a wiring harness deck works but no sound please help?
I am about to the same to my 97 JGC. There should be a wire with a spade plug that was all on it's own. It was plugged into the original stereo. That is the Amp turn on signal and it is a GROUND lead. Wire the Kenwood black wire to this wire with a matching plug and see if the amp turns on. Some people on the INTERNETS! will tell you to run the BLUE wire from the Kenwood, DON'T DO THAT. If the wire is looking for a ground it could damage the amp. Personally, I am dubious about this being a ground. But, if it is seeking a ground and you give it 12VDC from the BLUE wire, it could break the amp. If you give the wire a GROUND signal when it is seeking 12VDC, no damage. Better to try the gounding bit first. If it does not work, momentarily connect the blue to this wire whit the stereo powered up (turn down the volume to about 20% first). It should kick the amp on and make beautiful sounds once this wire is properly connected to the Kenwood. Connect aftermarket harness remote wire to power antenna wire on oem harness adapter. should work fine
How do I install a kenwood Car stereo in a ford ED falcon?
I will try to make this as simple as possible starting with the tools you will need. Phillips Head screw driver or cordless drill Pointy nose plyers and wire stripper Soldering iron and solder Something to test your wiring to see which one has power Heat shielding or electrical tape I think that's it! The red wire is normally power and the black ground, the speakers are something you can work out by sound or looking at the speakers they are connected to. The kenwood will come with a harness that plugs in the back of the steroe, the ford harness will not fit the kenwood so you will have to cut the ford harness (not to short from the plug) and then solder the kenwood harness on to it. Hope that helps.
