0
What else can I help you with?
Where do you find a wiring diagram for 1999 civic stereo?
If you are looking for the routing of the wiring for the speakers, you will have dificulty finding one. A wiring harnes connects to the back of the stereo and it would be wise to purchase an installation trim kit that come with a wiring harness to match your new stereo to that of the car.
How do you do the wiring in an 2002 Avalon stereo?
I bought a kit from all places, Wal-Mart. Turns out I bought the plastic parts thinking it had the wiring along with it but it didn't. But what it did have was the wiring diagram and I was able to match our 1999 Avalon with the wiring with the new stereo. With lots of thread baring and joining together, it works perfectly. Later at Wal-Mart, they do have the wiring kit that would have made it a whole lot easier.
What are the color codes for the wiring of a stereo in a 1984 Toyota truck?
Just read the irections on the stereo and rewire the whole thing. Its not as much trouble as it would seem. Took me about 30 minutes.
If wiring from stereo to trunk for CD changer exists from factory where would it be hidden?
tucked under the truck mat near the wheel wells
Does BestBuy carry Kenwood GPS?
Yes, BestBuy does in fact carry certain Kenwood GPS devices. They do not have every model that would be available on the Kenwood website but they do have specific models.
What logo has a w with a red triangle?
That would be Kenwood
88s10 Chevy is gray power feed tryin to install stereo wirin was set up differently when i got it?
If you are trying to install a stereo in a 1988 Chevy S10 and the wiring was set up differently when you got the truck the first step would be to identify the specific wiring setup that your truck has. You should be able to find wiring diagrams for the truck online or in a repair manual. Once you have identified the wiring setup you can then begin the installation process. Here are the steps you should follow: Gather all the necessary tools and materials. Turn off the battery and disconnect it. Remove the dashboard trim and any other components blocking access to the wiring. Identify the power source and ground locations. Connect the stereo wiring harness to the power source and ground. Connect the speaker wiring harnesses to the speakers. Connect the antenna cable to the antenna. Replace the dashboard trim and reconnect the battery. Test the stereo system.Once you have followed these steps you should be able to successfully install a stereo in your 1988 Chevy S10. Be sure to double-check your wiring connections to ensure that everything is securely connected.
Why your electric windows and stereo and electric mirrors wont work in your corsa?
Your electric windows, mirrors, and stereo might not work in your Corsa because of a blown fuse or exposed wiring. The easiest way to begin troubleshooting would be to check each fuse.
Where can you find a free stereo wiring diagram for a 2000 Jeep Cherokee?
Try the dealerships first. If you are putting in an aftermarket stereo I would recommend purchasing a connection adaptor. Thes allow you to plug your aftermaket stereo right into your factory harness without having to change or cut any of the factory wiring. They are available from most car audio retailers and larger electronics stores. They sell for $15 to $20 and are extremely simple to use.
How do you install a radio?
You will need to get a wire harness kit that is made for the type of stereo that you have and the car you drive. For instance, I have a 2003 Honda civic. The 2003 Honda civic is equiped with an Aiwa brand stereo stock. I'm not sure if this is for all civics, but for the 2003 Civic they installed Aiwa brand (my 2004 Suzuki Aero is equipped with a Clarion stock). Now, If I were to buy an Aiwa brand stereo wiring would be no problem, I would unplugg the old stock stereo and install the new one, but i hate Aiwa and I wanted to install a kenwood. Now I have two choices, 1) Buy any kenwood wiring kit and splice the wires (cut the old wires and cob job the rest, which I later found out take time and practice) or 2)buy an expensive hard to find Aiwa to Kenwood wiring adapter ($100 or more). I decided to splice the wires. Luckily my brother knows how to do this and he did it for me, but he told me that he ruined about three stereos before becoming a pro at it. The best thing to do is unplug your car battery, but since he was an expert we skipped that part. Also, air bags can explode if you were to short a wire. I did it myself on my Suzuki with success with out unpluging the battery. Just make sure you can read a wire chart and always connect the power wire last (keep your car off). Now the next step is to get the stereo chasis to fit. The best thing is to look at other cars of your type and see how they were installed and look. Every stereo is installed and will look different. The Civic and the Suzuki stereos are connected to a curved molded dashboard so I had to be creative. Flip face stereos seem to be the best because the hide into the dash. Other stereos will stick out a bit. . first you need to determin the vehicle and radio type.
How do you replace stock stereo on 95 Saturn SL2?
Having just finished spending 4 days tracking wires to install a stereo in a 95 SL1, I would suggest going to your local car audio store and purchasing a wiring harness. It'll run you about $15 and save you LOTS of headaches. Saturn's stereo harness is an intergal part of the dash wiring, so there are things going through your stereo that have nothing to do with it; i.e. dash lights, back up lights, door chime, etc. The harness will incorporate all of that for you.
What would cause a car to not start after stereo installation?
Could be a short that burn out a staring relay fuse. You're going to need some wiring diagrams, bro.
